Pioneer VSX-9300TX manual Additional information, No sound, Symptom, Cause, Remedy

Additional information 12

No sound

Symptom	Cause	Remedy
No sound is output when an	• Improper connections.	• Make sure you have properly connected the component
input source is selected.		to the corresponding input on the back of the receiver
		(see Connecting your equipment on page 15).

•Sound is muted or the volume is turned down.

• Press MUTE or adjust the volume accordingly.

• Speakers are turned off or selected	• Press SPEAKERS to select the proper speaker set (see
improperly with the SPEAKERS switch.	Switching the speaker system on page 67).
• The input signal type is incorrect.	• Press SIGNAL SELECT to select the proper input signal
	(see Selecting the input signal type on page 42).

•The multichannel analog inputs are selected.

•Press MULTI CH INPUT again (see Using the multichannel analog inputs on page 41).

No sound output from the front	• The front speakers aren’t connected	• See Installing your speaker system on page 28 to
speakers.	properly.	connect them properly.

No sound from the surround or center speakers.

• Speaker settings are incorrect. (for	• Check you speaker settings in Speaker Setting on
example, they have been set to NO).	page 51.
• The surround and/or center levels are	• Check the levels in Channel Level on page 52.
turned down.

	• The surround and/or center speakers aren’t	• Check Installing your speaker system on page 28 to
	connected properly.	make sure the speakers are connected correctly.
	• The STEREO listening mode has been	• Choose a surround listening mode (see Listening in
	selected.	surround sound on page 37).
No sound from surround back	• Surround back speakers are set to NO.	• Set the surround back speakers to LARGE or SMALL
speakers.		(see Speaker Setting on page 51).
	• The SB CH mode is switched off.	• Set the surround back channel to SB CH ON (see
		page 43).
	• The source is not a 6.1 channel playback	• Choose an advanced effect listening mode (see
	source.	Listening in surround sound on page 37).
	• The surround back speakers aren’t	• Check Installing your speaker system on page 28 to
	connected properly.	make sure the speakers are connected correctly.
	• The surround back channel is on the 1	• Connect the speaker to the surround back left channel
	speaker setting, and your speaker is	output (Installing your speaker system on page 28).
	connected to the right channel output.
	• The SB CH MODE is switched to AUTO and	• You can still listen with surround back sound by setting
	the Dolby Surround EX / DTS ES software	the surround back channel to SB CH ON (page 43).
	you’re playing has no flag to indicate it is 6.1
	compatible.
No sound from subwoofer.	• The bass attenuator is set too low (for	• See Bass Peak Level on page 86 to adjust the setting.
	example, the -80setting).

•The subwoofer isn’t connected properly, or it is switched off.

•Connect or switch on the subwoofer (see Installing your speaker system on page 28).

•Make sure the sleep function on your subwoofer isn’t activated.

• The subwoofer's settings are incorrect.

•Set the subwoofer (see Speaker Setting on page 51) to YES or PLUS.

• The crossover frequency is set too low.

•Set the crossover frequency to a (higher) frequency that matches your speaker characteristics (see Crossover Network on page 80)

• There is very little low frequency information	• Change your subwoofer setting to one of the following in
in your source.	the Speaker Setting on page 51:
	Front: SMALL / Subwoofer: YES
	Front: LARGE / Subwoofer: PLUS
• The subwoofer's levels are too low.	• See Channel Level on page 52 to check the speaker
	levels.
	• Check the volume control on the subwoofer to make
	sure it is turned up.

89

En