3 ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP (1) reduces risk of accidental scalding. To set the maximum hot water temperature of your faucet, all you need to do
is adjust the setting on the HOT LIMIT SAFETY STOP (1).
Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before making adjustment to HOT LIMIT STOP (1). Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1). Pull forward and rotate counterclockwise one number to limit hot water temperature. Use ARROW (3) on CARTRIDGE (4)
and NUMBERS (5) on HOT LIMIT STOP (1) for indication.
|
|
|
|
| 3 |
|
|
|
|
| 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 357911 | 3 |
| 1 | 5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
1 | 1 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| 5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| 1 |
|
|
|
|
|
| 2 |
|
|
|
|
| HOTTER |
|
|
|
|
|
|
|
|
|
| 1 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| 15 | (Smaller Numbers) | ||||||
|
|
|
|
|
|
|
|
|
|
| 3 |
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | 5 |
|
| 1 | 1 | 0 1 3 5 7 9 11 13 15 | ||||||
|
|
|
|
|
|
|
| 7 | 9 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| 4 | 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 | |
|
|
|
|
| 4 |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 51 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 13 | 1 | |
|
|
|
|
| COLDER |
|
| 5 | 7 |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 9 | 1 |
|
| 2 |
|
|
|
| (Larger Numbers) | 1 | 3 |
|
|
|
| 1 | |||||
|
|
|
|
| 0 1 3 5 7 9 11 13 15 |
|
|
|
|
|
| |||||||
5 TO GAIN ACCESS TO VALVE FOR SERVICING
4 | INSTALL HANDLE, DIVERTER KNOB, TUB |
SPOUT AND SHOWER |
Thread DIVERTER KNOB (1) onto diverter stem. Hold ADAPTER (2) onto VALVE STEM (3) and install ADAPTER SCREW (4) through ADAPTER (2) into VALVE STEM (3).Tighten ADAPTER SCREW (4) to secure ADAPTER (2) to VALVE STEM (3).
Install HANDLE BASE (5) onto ADAPTER (2). Insert SET SCREW (6) into HANDLE BASE (5). Align HANDLE BASE (4) and tighten with HEX WRENCH
(7)supplied.
Remove pipe cap and plug from shower and tub rough piping.
Install SPOUT ESCUTCHEON (9) onto TUB SPOUT (10). Apply sealant or Teflon tape to threads of tub filler nipple. Thread TUB SPOUT (10) onto tub nipple. Install SHOWER ESCUTCHEON (11) onto SHOWER ARM (12). Apply sealant or Teflon tape to threads on both ends of SHOWER ARM (12) and thread longer leg of SHOWER ARM (12) into shower elbow. Thread SHOWER HEAD (13) onto SHOWER ARM (12).
CAUTION: Protect finish on SHOWER HEAD and ARM when installing.
11
SHR.
ELBOW
Unthread LEVER HANDLE, loosen SET SCREW and pull HANDLE off valve stem.
To remove Escutcheon assembly reverse steps in Step 3.
VALVE LEAKS WHEN SHUT OFF
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean
Turn on water supply and see above for installing TRIM and HANDLE.
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7) and clean valve thoroughly.
Examine balancing unit and check condition of
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting. Top flange should
BACK TO BACK INSTALLATION
13
PIPE
12PLUG
1 
5 | 4 |
|
|
|
|
| |
| 6 | 2 | 3 TUB |
| 7 |
| NIPPLE |
|
|
|
| 9 |
10 | PIPE |
| CAP |
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should butt up against top of casting.
Reassemble FIXATION RING (4) and CARTRIDGE (1).
6
8
7 5
4 |
| LARGE OUTLET |
|
| 1 |
|
| 5 |
|
| INLETS |
3 | 9 | 2 |
|
ROTATE 180˚
BACK TO BACK INSTALLATION
M968836 Rev . 1 . 4
