C 2010 AOC.All Rights Reserved | AOC i2340Ve instruction

c 2010 AOC.All Rights Reserved.

www.aoc.com

c 2010 AOC.All Rights Reserved.

Image 1

AOC i2340Ve manual c 2010 AOC.All Rights Reserved

Contents

c 2010 AOC.All Rights Reserved Power SafetyInstallation Cleaning Warranty Statement for Europe ServiceWarranty Statement for North & South America excluding Brazil EPEAT Declaration National Conventions Safety Power Installation Cleaning Other Contents in Box Setup Please setup or remove the base following the steps as below Setup Setup Stand & BaseRemove Adjusting Viewing Angle Connecting the Monitor Setting Optimal Resolution AdjustingWindows Vista 6 Set the resolution SLIDE-BAR to 1920 by 5 Click Display Settings 5 Click SETTINGS Windows XPFor Windows XP 2 Click CONTROL PANEL 3 Click Appearance and Themes 2 Click SETTINGS 3 Click CONTROL PANEL Windows ME/2000For Windows ME/2000 Source/Auto Hotkeyse-sensor Menu/Enter Basic and simple instruction on the control keys OSD Setting Luminance to enter, and press or to adjust Press to exitPress Menu to display menu Press or to select Luminance, and press to enter Press or to select submenu, press Adjust to Gamma1 Backlight AdjustmentAdjust to Gamma Enable dynamic contrast ratio Setup , and press Image Setupadjust Press to exit Press Menu to display menu reduce Press Menu to display menu Press or to select Color Color TemperatureTemperature, and press to enter Press or to select submenu, press Cool Normal Color Color BoostBoost , and press Disable or Enable Nature Skin Mode Disable or Enable Full Enhance ModeDisable or Enable Green Field Mode Disable or Enable Sky-blue Mode Press Menu to display MENU Press or to select Picture Picture BoostBoost and press to enter Adjust Frame Brightness Adjust Frame SizeAdjust Frame Contrast Adjust Frame horizontal Position OSD Setup Adjust the horizontal position of OSD SetupAdjust the vertical position of OSD Timeout Extra Analog AutoDigital Press Menu to display menu Press or to select Reset, and Resetpress to enter Press or to select YES or NO Press to exit Reset the menu to default Reset Press Menu to display menu Press or to select Exit and Exitpress to enter Full Power Mode LED IndicatorStatus LED Color Monitor Driver DriverWindows 5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 7.Click the “Driver” tab “Update Driver... “and then9. Select Let me pick from a list of device drivers on my computer 13. Close all open windows and remove the CD 3. Click Advanced Settings 2. Click Personalization and then Display Settings 8. Select your monitor model and click on the Next button 5. Click Update Driver... in the Driver tab 2. Click on the Start button and then click on Control Panel 1. Start Windows XP3. Select and click on the category „Appearance and Themes‟ 4. Click on the Display Item 7. Click on the Driver tab and then click on Update Driver... button 5. Select the Settings tab then click on the Advanced button6. Select Monitor tab If the Properties button is active, click on Properties button 12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Sensor e-Saver Screen+ Problem & Question TroubleshootPower LED Is Not ON Ghosting Shadowing Problem Monitor Is Stuck In Active General Specification Specification Preset Display Modes Pin Assignments Plug & Play DDC2B Feature Plug and Play FCC Notice Regulation WEEE Declaration Only for North and South American, excluding Brazil EPEAT DeclarationFor Germany For Brazil Warranty Statement for Europe Service Information in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil ARGENTINA http//ar.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterBOLIVIA http//bo.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter