Yes or no, Reset the menu to default | AOC i2340Ve guide

Reset

Reset

yes or no

Reset the menu to default

34

Image 34

AOC i2340Ve manual yes or no, Reset the menu to default

Contents

c 2010 AOC.All Rights Reserved Installation SafetyPower Cleaning Warranty Statement for North & South America excluding Brazil ServiceWarranty Statement for Europe EPEAT Declaration Safety National Conventions Power Installation Cleaning Other Setup Contents in Box Please setup or remove the base following the steps as below Setup Setup Stand & BaseRemove Adjusting Viewing Angle Connecting the Monitor Setting Optimal Resolution AdjustingWindows Vista 5 Click Display Settings 6 Set the resolution SLIDE-BAR to 1920 by For Windows XP Windows XP5 Click SETTINGS 2 Click CONTROL PANEL 3 Click Appearance and Themes 2 Click SETTINGS 3 Click CONTROL PANEL Windows ME/2000For Windows ME/2000 e-sensor HotkeysSource/Auto Menu/Enter OSD Setting Basic and simple instruction on the control keys Press Menu to display menu Press or to select to enter, and press or to adjust Press to exitLuminance Luminance, and press to enter Press or to select submenu, press Adjust to Gamma Backlight AdjustmentAdjust to Gamma1 Enable dynamic contrast ratio adjust Press to exit Image SetupSetup , and press Press Menu to display menu reduce Press Menu to display menu Press or to select Color Color TemperatureTemperature, and press to enter Press or to select submenu, press Normal Cool Color Color BoostBoost , and press Disable or Enable Green Field Mode Disable or Enable Full Enhance ModeDisable or Enable Nature Skin Mode Disable or Enable Sky-blue Mode Press Menu to display MENU Press or to select Picture Picture BoostBoost and press to enter Adjust Frame Contrast Adjust Frame SizeAdjust Frame Brightness Adjust Frame horizontal Position OSD Setup Adjust the vertical position of OSD OSD SetupAdjust the horizontal position of Timeout Extra Analog AutoDigital Press Menu to display menu Press or to select Reset, and Resetpress to enter Press or to select YES or NO Press to exit Reset Reset the menu to default Press Menu to display menu Press or to select Exit and Exitpress to enter Status LED IndicatorFull Power Mode LED Color Monitor Driver DriverWindows 5.Click the “Advanced Settings” button 4.Ckick on the “Change display settings” button6.Click the “Monitor” tab and then click the “Properties” button 7.Click the “Driver” tab “Update Driver... “and then9. Select Let me pick from a list of device drivers on my computer 13. Close all open windows and remove the CD 2. Click Personalization and then Display Settings 3. Click Advanced Settings 5. Click Update Driver... in the Driver tab 8. Select your monitor model and click on the Next button 3. Select and click on the category „Appearance and Themes‟ 1. Start Windows XP2. Click on the Start button and then click on Control Panel 4. Click on the Display Item 6. Select Monitor tab 5. Select the Settings tab then click on the Advanced button7. Click on the Driver tab and then click on Update Driver... button If the Properties button is active, click on Properties button 12. Select your monitor model and click on the Next button 11. Click on the Open button, then click the OK button13. Click on the Finish button then the Close button Windows ME i-Menu e-Sensor e-Saver Screen+ Power LED Is Not ON TroubleshootProblem & Question Ghosting Shadowing Problem Monitor Is Stuck In Active Specification General Specification Preset Display Modes Pin Assignments Plug and Play Plug & Play DDC2B Feature Regulation FCC Notice WEEE Declaration For Germany EPEAT DeclarationOnly for North and South American, excluding Brazil For Brazil Service Warranty Statement for Europe Information in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil BOLIVIA http//bo.aoc.com/support/findservicecenter USA http//us.aoc.com/support/findservicecenterARGENTINA http//ar.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter