Manuals / AOC / Car Audio and Video / Car Video System

AOC i2340Ve manual e-Sensor

Models: i2340Ve

1 63

Download 63 pages 8.5 Kb

Page 48

Image 48

e-Sensor

Welcome to AOC “e-Sensor” !

AOC “e-Sensor” is an infrared sensor embedded in your monitor bezel; it enables your monitor to turn off while you are away. To make it work, please use the designated hotkey to set up. Once you press the hotkey, you shall see the menu display below:

The detectable range of the sensor is around 120cm, you may select near, average, or far to set the ideal range within which you would like the eSensor detect you.

Under “Monitor Off” section, you may decide when you would like your monitor to automatically turn off after you are away (never, 10min, 20min, 30min… 60min).

Note: Please do NOT block the e-Sensor on the bezel, which is located on the left of AOC logo.

Page 48

Image 48

Contents

c 2010 AOC.All Rights Reserved Safety PowerInstallation CleaningService Warranty Statement for EuropeWarranty Statement for North & South America excluding Brazil EPEAT DeclarationSafety National ConventionsPower Installation Cleaning Other Setup Contents in BoxSetup Stand & Base Please setup or remove the base following the steps as below SetupRemove Adjusting Viewing Angle Connecting the Monitor Adjusting Setting Optimal ResolutionWindows Vista 5 Click Display Settings 6 Set the resolution SLIDE-BAR to 1920 byWindows XP 5 Click SETTINGSFor Windows XP 2 Click CONTROL PANEL 3 Click Appearance and ThemesWindows ME/2000 2 Click SETTINGS 3 Click CONTROL PANEL5 Click SETTINGS For Windows ME/2000Hotkeys Source/Autoe-sensor Menu/EnterOSD Setting Basic and simple instruction on the control keysto enter, and press or to adjust Press to exit LuminancePress Menu to display menu Press or to select Luminance, and press to enter Press or to select submenu, pressBacklight Adjustment Adjust to Gamma1Adjust to Gamma Adjust to GammaImage Setup Setup , and pressadjust Press to exit Press Menu to display menureduce Color Temperature Press Menu to display menu Press or to select ColorTemperature, and press to enter Press or to select submenu, press to enter, and press or to adjust Press to exitNormal CoolColor Boost ColorBoost , and press adjust Press to exitDisable or Enable Full Enhance Mode Disable or Enable Nature Skin ModeDisable or Enable Green Field Mode Disable or Enable Sky-blue ModePicture Boost Press Menu to display MENU Press or to select PictureBoost and press to enter adjust Press to exitAdjust Frame Size Adjust Frame BrightnessAdjust Frame Contrast Adjust Frame horizontal PositionOSD Setup Setup , and pressadjust Press to exit Press Menu to display menuOSD Setup Adjust the horizontal position ofAdjust the vertical position of OSD TimeoutExtra Setup , and pressadjust Press to exit Press Menu to display menuAuto AnalogDigital Reset Press Menu to display menu Press or to select Reset, andpress to enter Press or to select YES or NO Press to exit Reset Reset the menu to defaultyes or no Exit Press Menu to display menu Press or to select Exit andpress to enter LED Indicator Full Power ModeStatus LED ColorDriver Monitor DriverWindows 4.Ckick on the “Change display settings” button 5.Click the “Advanced Settings” button6.Click the “Monitor” tab and then click the “Properties” button “Update Driver... “and then 7.Click the “Driver” tab9. Select Let me pick from a list of device drivers on my computer 13. Close all open windows and remove the CD 2. Click Personalization and then Display Settings 3. Click Advanced SettingsWindows Vista 5. Click Update Driver... in the Driver tab 8. Select your monitor model and click on the Next buttonWindows XP 1. Start Windows XP2. Click on the Start button and then click on Control Panel 3. Select and click on the category „Appearance and Themes‟5. Select the Settings tab then click on the Advanced button 7. Click on the Driver tab and then click on Update Driver... button6. Select Monitor tab If the Properties button is active, click on Properties button11. Click on the Open button, then click the OK button 12. Select your monitor model and click on the Next button13. Click on the Finish button then the Close button Windows ME Windowsi-Menu e-Sensor e-Saver Screen+ Troubleshoot Problem & QuestionPower LED Is Not ON Ghosting Shadowing ProblemMonitor Is Stuck In Active Specification General SpecificationPreset Display Modes Pin Assignments Plug and Play Plug & Play DDC2B FeatureRegulation FCC NoticeWEEE Declaration EPEAT Declaration Only for North and South American, excluding BrazilFor Germany For BrazilService Warranty Statement for EuropeInformation in this document is subject to change without notice Warranty Statement for North & South America excluding Brazil USA http//us.aoc.com/support/findservicecenter ARGENTINA http//ar.aoc.com/support/findservicecenterBOLIVIA http//bo.aoc.com/support/findservicecenter CHILE http//cl.aoc.com/support/findservicecenter