APC BE600N-BR manual Turn On the Back-UPS, Install PowerChute Software, Status Indicators

Turn On the Back-UPS

Press the Power ON button located on the top of the Back-UPS. The green LED will illuminate and a single short beep will be audible indicating that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first eight hours while connected to utility power. The Back-UPS battery will charge while the Back- UPS is switched ON or OFF. Do not expect full battery run capability during the initial charge time.

Install PowerChute Software

Install the optional PowerChute CD in the computer and follow the prompts to install the software.

Status Indicators

Status	LED Indicator	Audible Indicator On	Audible Indicator Off
Power On
The Back-UPS is supplying utility power to	The green LED illuminates.	N/A	N/A
connected equipment.
On Battery	The green LED illuminates.The	Back-UPS beeps four times every	Beeping stops when power transfers
Back-UPS supplying battery	LED is not illuminated during the		back to utility power or the Back-UPS is
		30 seconds.
power to battery back-up outlets.	beeps.		turned OFF.
Low Battery warning			The beeping stops when power transfers
The Back-UPS is supplying battery power	The green LED illuminates with	The Back-UPS emits rapid beeping,
			back to utility power or the Back-UPS is
to the battery back-up outlets and the battery	rapid green flashes.	(every 1/2 second).
			turned OFF.
is near a total discharge state.
Check Battery
• The battery is disconnected.	The red LED flashes.	Constant tone	Back-UPS is turned Off.
• The battery needs to be charged, or replaced.
Overload Shutdown
While on battery power an overload condition
has occurred in one or more of the battery	The red LED illuminates.	Constant tone	Back-UPS is turned Off.
back-up outlets while the Back-UPS is operating
on battery power.
AVR	When the AVR feature is activated	N/A	N/A
	the amber LED illuminates.
Sleep Mode			The beeping stops when:
While on battery power the battery is		The Back-UPS beeps once every	• Utility power is restored
completely discharged. The Back-UPS will	N/A
			• If utility power is not restored within
“awaken” once utility power is restored.		four seconds.
			32 seconds
			• The Back-UPS is turned OFF

Voltage Sensitivity Adjustment (optional)

The Back-UPS detects and reacts to line voltage distortions by transferring to battery back-up power to protect connected equipment. In situations where either the Back-UPS or the connected equipment is too sensitive for the input voltage level it is necessary to adjust the transfer voltage.

1.Connect the Back-UPS to a wall outlet. The Back-UPS will be in Standby mode, no indicators will be illuminated.

2.Press and hold the Power On button for 10 seconds. The red LED flashes, to indicate that the Back-UPS is in Program mode.

3.The green or red LEDs will flash to indicate the current sensitivity level. Refer to the table for an explanation of the transfer voltage sensitivity levels.

4.To select LOW sensitivity, press and hold the Power On button until the green LED flashes.

5.To select MEDIUM sensitivity, press and hold the Power On button until the red LED flashes.

6.To select HIGH sensitivity, press and hold the Power On button until the green and red LEDs flash alternately.

7.To exit Program mode wait five seconds and all LED indicators will extinquish. Program mode is no longer active.

LED Flashes	Sensitivity Setting	Input Voltage Range	Recommended Use
Green	LOW	115 Vac: 88 Vac to 143 Vac	Input voltage is extremely low or extremely high. Not
		220 Vac: 176 Vac to 264 Vac	recommended for computers.
Red	MEDIUM (factory default)	115 Vac: 88 Vac to 143 Vac	Use when the Back-UPS frequently switches to battery
		220 Vac: 176 Vac to 264 Vac	operation.
Alternating Green/Red	HIGH	115 Vac: 96 Vac to 137 Vac	Use when connected equipment is sensitive to voltage
		220 Vac: 192 Vac to 252 Vac	fluctuations.

2