APC BE700G Specifications Order Replacement Battery, Warranty, Service, Wall-mounting Template

Specifications Order Replacement Battery

Input	Voltage	230 Vrms Nominal
	Frequency	50/60 Hz (auto sensing)
	Brownout Transfer	180 Vrms, typical
	Over-voltage Transfer	266 Vrms, typical
Output	Voltage On Battery	230 Vac rms +/- 8%
	Total Amperage (8 outlets)	10 Amps (including UPS output)
	UPS Capacity (4 outlets)	550VA/330W		700VA/405W
	Frequency - On Battery	50/60 Hz +/-1 Hz
	Transfer Time	6 ms typical, 10 ms maximum
Protection	AC Surge Protection	Full time, 451 joules
and Filter
	Phone/fax/DSL Surge	Single line (2-wire)
	Protection
	Network Surge Protection	10/100Base-T Ethernet
	EMI/RFI Filter	Full time
	AC Input	Resettable circuit breaker
Battery	Type	Sealed, maintenance-free lead acid
	Average Life	3 - 5 years depending on the number
		of discharge cycles and
		environmental temperature
Physical	Net Weight	6.4kg	6.8kg
	Dimensions (H x W x D)	285 x 230 x 86 mm
		(11.2 x 9.1 x 3.4 in)
	Operating Temperature	0oC to 40 oC (32 oF to 104 oF)
	Storage Temperature	-15 oC to 45 oC (5 oF to 113 oF)
	Operating Relative	0 to 95% non-condensing
	Humidity
	Operating Elevation	0 to 3000 m (0 to 10,000 ft)
Safety/	SKU	Approval
Regulatory
	BE550G-AZ/BE750G-AZ	A-Tick & C-Tick
	BE550G-RS/BE750G-RS	GOST
	BE550G-GR/BE700G-GR	GS
	BE550G-FR/BE700G-FR	CE per IEC62040-1-1 & IEC60884-
		1, GS, GOST-PCT
	BE550G-UK/BE700G-UK
	BE550G-IT/BE700G-IT
	EMC Compliance	CE per EN62040-2/EN55022 & C-
		Tick

Replace with a genuine APC battery. Replacement batteries can be ordered from www.apc.com (valid credit card required). For Back-UPS BE 550, order RBC110. For Back- UPS BE 700, order RBC17.

Warranty

The standard warranty is 3 years from the date of purchase in the EU, 2 years outside of the EU. APC’s standard procedure is to replace the original unit with a factory reconditioned unit. Customers who must have the original unit back due to assigned asset tags and set depreciation schedules must declare such a need at first contact with APC Technical Support. APC will ship the replacement unit once the defective unit is received by the repair department or cross- ship upon the provision of a valid credit card number. The customer pays for shipping to APC, and APC pays ground

Service

DO NOT RETURN Back-UPS to the place of purchase under any circumstances.

1.Verify the battery is connected and that the circuit breaker is not tripped.

2.If there are still problems or questions, contact APC.

3.Before contacting APC, have the purchase date, UPS model, and serial number (on bottom of unit) available.

4.If the Technical Support Representative cannot solve the problem, the representative will issue a Return Material Authorization Number (RMA#) and a shipping address.

5.Pack the unit in its original packaging. If the original packaging is not available, ask APC Technical Support about obtaining a new set. Pack the unit properly to avoid damage in transit. Never use foam beads for packaging. Damage sustained in transit is not covered under warranty (insuring the package for full value is recommended).

6.Write the RMA# on the outside of the package.

7.Return the unit by insured carrier to the address given to you by APC Technical Support.

APC Worldwide Customer Support

UPS Wall Installation	Technical Support	http://www.apc.com/support
The UPS can be installed vertically or horizontally to a wall. Use the template to assist
	Internet	http://www.apc.com
with installation and a fastener (not included) that can support at least 6.8 kg.

1.Hold the template against the wall surface and use a nail or pin to mark the center of each hole.

2.Install a fastener into the wall at the marked locations. Allow 8 mm of the fastener to protrude from the wall.

3.Install the unit on the wall, using the fasteners.

Worldwide	+1 800 555 2725
Australia	1 800-652725
European Union	000 353 91 7020002725

165 mm

(6.50 in.)

Wall-mounting Template

© 2011 APC by Schneider Electric. APC and the APC l ogo are owned by Schneider Electric Industries	990-3488A-001
S.A.S., American Power Conversion Corporation, or their affiliated companies. All other trademarks are	06/2011
property of their respective owners.