Model 8051 Flush Mount Sensor

Installation Instructions

Introduction

The 8051 is a temperature sensor. It can be used to remotely measure temperature with compatible Aprilaire® thermostats and support modules.

Installation Instructions

1.Select a location for mounting the sensor. Locate the sensor as you would locate a thermostat.

•Mount on an interior wall, in a frequently occupied space.

•Keep the sensor 18” away from an outside wall.

•DO NOT mount the sensor:

–Behind doors, in corners or other dead air spaces.

–In direct sunlight or near lamps, appliances, dimmer switches or other sources of heat.

–On an outside wall or wall exposed to an unconditioned space (i.e. garage).

–In the flow path of a supply register, in stairways or near outside doors.

–On a wall where a concealed pipe or ductwork could influence the sensor.

–Near sources of electrical interference such as light switches.

Maximum wire length from the sensor to the thermostat or support module is 300 feet.

2.Install the sensor – see back page.

3.Disconnect power to the thermostat or support module to which the sensor will be wired.

CAUTION

Damage to components can occur if power is not disconnected.

4.Verify the sensor resistance.

Use an ohm-meter or multimeter to measure the resistance of the sensor. Measure at the wires near the thermostat or support module to check any wire splices. Confirm the resistance corresponds (within 5%) to the temperature where the sensor is installed.

The following table shows the correct resistance at various ambient temperatures without the sensor wires attached to a thermostat or support module.

Temperature (°F)

Resistance (k )

 

 

30

34.6

 

 

40

26.1

 

 

50

19.9

 

 

60

15.3

 

 

70

11.9

 

 

80

9.4

 

 

90

7.4

 

 

100

5.9

 

 

5. Wire the sensor to the component.

CAUTION

Excessive bare wire can lead to shorts. Strip only as much insulation as is necessary.

•The sensor is not polarity specific. Either sensor lead may be connected to either terminal on the component to which it is wired. To select the appropriate terminals for wiring please see the installation manual for the thermostat or support module.

•Use care when routing and stripping the wire. Sharp bends (kinks) or cuts in the wire (particularly susceptible where the insulation has been stripped) can lead to eventual conductor failure.

6.Reconnect power to the thermostat or support module to which the sensor is installed.

Sensor Specifications

Voltage

20-30 VAC

 

 

Resistance @ 25°C (77°F)

10 k

 

 

Tolerance @ 25°C (77°F)

±3%

 

 

61000944A AA 8051 Flush Mount Sensor Install.indd 1

3/28/12 11:38 AM

Page 1 Page 2
Page 1
Image 1
Aprilaire installation instructions Model 8051 Flush Mount Sensor Installation Instructions, Introduction
Page 1 Page 2

8051 specifications

The Aprilaire 8051 is a state-of-the-art thermostat designed for optimal home climate control. Known for its innovative technology and user-friendly features, it stands out in the crowded market of smart thermostats. One of the main highlights of the Aprilaire 8051 is its ability to control humidity levels, which is crucial for both comfort and health. It utilizes an integrated humidity sensor that allows users to maintain ideal humidity levels throughout their home, preventing issues such as mold growth and dust mite infestation.

The Aprilaire 8051 features a touchscreen interface that is both intuitive and easy to navigate. Users can quickly access temperature settings, humidity controls, and system modes with just a few taps. The display is designed for clear visibility and can be adjusted to suit the user's preferences. This thermostat is also equipped with Wi-Fi connectivity, enabling remote access via a smartphone app. This feature allows homeowners to adjust settings while away from home, ensuring that their environment is always comfortable upon return.

Another notable characteristic of the Aprilaire 8051 is its compatibility with a wide range of heating, ventilation, and air conditioning (HVAC) systems. This versatility makes it suitable for various home setups, whether they involve central air systems, heat pumps, or zoned heating systems. Additionally, it supports multi-stage heating and cooling, providing precise control over the home’s climate.

Energy efficiency is a key priority in the design of the Aprilaire 8051. The thermostat has features that promote energy-saving practices, such as programmable settings that allow users to set temperature schedules based on their daily routines. The learning capability of the thermostat optimizes energy use by adapting to the homeowner's preferences over time.

Moreover, the Aprilaire 8051 prioritizes air quality. It can work in conjunction with air purifiers and ventilation systems to ensure that indoor air remains fresh and clean. Notifications and reminders for filter changes help maintain optimal performance, further enhancing air quality and ensuring system efficiency.

In summary, the Aprilaire 8051 is an advanced thermostat that embodies the perfect blend of technology, energy efficiency, and user convenience. With its ability to control humidity, intuitive touchscreen interface, Wi-Fi connectivity, and compatibility with various HVAC systems, it is an excellent choice for homeowners looking to enhance their living environment.
Top Page Image Contents