INSTALLATION

INSTALACION

INSTALLATION

4

3 2

1

FIGURE 3

GUN INSTALLATION

As shipped from the factory, the MIG PAK 10 is ready to feed

.023" – .025" (0.6 mm) solid wire. If .030" (0.8 mm) solid wire

is to be used, change the contact tip to the appropriate size.

Connecting Gun Cable to the MIG PAK

1.Refer to Figure 1 Unplug the machine or turn power switch to the OFF “O” position.

2.Pass the insulated terminals of the gun trigger control leads, one at a time, through the Gun Cable and Control Lead Access Slot (2) in the case front. The leads are to be routed under the Wire Feed Gearbox (6) and through the Cable Hanger (7) on the inner panel.

3.Insert the connector on the gun conductor cable through the Gun Cable Access Hole (2) in the MIG PAK case front. Make sure the connector is all the way in the brass connector block. Unscrew thumbscrew on the connector block a few turns if gun connector will not insert fully. Rotate the connector so control leads are on the under-

side and tighten the Thumbscrew (8) in the connector block.

4

3 2

1

FIGURA 3

INSTALACION DE LA ANTORCHA

De fábrica , la antorcha de la MIG PAK 10 está lista para alimentar alambre de 0.6 mm (.023" -.025"). Si se va a utilizar alambre de 0.8 mm (.030"), cambie la punta de contacto a l tamaño adecuado.

Conexión del Cable de la Antorcha a la MIG PAK

1.Consulte la Figura 1. Desconecte la máquina o coloque el interruptor de encendido en la posición “O” (APAGA- DO).

2.Pase una por una las puntas aisladas de los cables de control del gatillo de la antorcha, a través de la Ranura de Acceso del Cable de Control y del Cable de la Antorcha (2) en el frente del gabinete. Los cables deberán pasar por debajo de la Caja de Engranajes de Alimentación de Alambre (6) y a través del Sujetador de Cable (7) en el panel interno.

3.Inserte el conector del cable conductor de la antorcha a través del Orificio de Acceso del Cable de la Antorcha (2), en el frente del gabinete de la MIG PAK. Asegúrese de que el conector entre totalmente en el bloque conec- tor de latón. Si el conector de la antorcha no entra por completo, desenrosque un poco el tornillo mariposa del bloque conector. Gire el conector para que los cables de control queden abajo, y apriete el Tornillo Mariposa (8) del bloque conductor.

4

3 2

1

FIGURE 3

MONTAGE DU PISTOLET

Àsa sortie d'usine, la MIG PAK 10 est prête pour recevoir du fil plein de 0,023-0,025 po (0,6 mm). Si l'on doit utiliser du fil de 0,030 po (0,8 mm), changer le tube contact pour la grosseur appropriée.

Raccordement du câble du pistolet à la MIG PAK

1.Voir la figure 1. Débrancher l'appareil ou pousser l'inter- rupteur d'alimentation sur OFF «O».

2.Faire passer les cosses isolées des fils de commande de la gâchette du pistolet, une par une, dans la fente d'accès des fils de commande et du câble du pistolet (2) à l'avant du boîtier. On doit faire passer les fils sous la boîte d'en- grenages du dévidoir (6) et dans le support de câble (7) sur le panneau intérieur.

3.Faire passer le connecteur sur le câble conducteur du pistolet dans le trou d'accès du câble du pistolet (2) à l'a- vant du boîtier de la MIG PAK. S'assurer que le con- necteur est enfoncé à fond dans le bloc connecteur en laiton. Dévisser la vis à ailettes sur le bloc connecteur de quelques tours si le connecteur du pistolet n'entre pas à fond. Faire tourner le connecteur de façon que les fils de commande se trouvent vers le bas et serrer la vis à ailettes (8) dans le bloc connecteur.

13

Page 13
Image 13
Lincoln Electric MIG-PAK 10 Installation Instalacion, GUN Installation, Instalacion DE LA Antorcha, Montage DU Pistolet

MIG-PAK 10 specifications

The Lincoln Electric MIG-PAK 10 is a versatile and user-friendly MIG welding machine tailored for light industrial applications and DIY enthusiasts. This compact welder is designed for both professionals and hobbyists, offering a perfect blend of performance and portability. It is particularly suitable for welding light to medium-gauge steel, stainless steel, and aluminum.

One of the standout features of the MIG-PAK 10 is its economy of size without compromising on power. Weighing in at just around 40 pounds, it is easily transportable, making it a practical choice for on-site jobs or small workshops. Its compact dimensions allow it to fit into tight spaces, facilitating accessibility for various welding tasks.

The MIG-PAK 10 employs a built-in gas solenoid that facilitates gas shielding for improved arc stability and weld quality. It is compatible with both shielding gas and flux-cored wire, offering flexibility depending on the application requirements and working environment. This dual capability is particularly beneficial for outdoor welding, where wind can disrupt gas shielding.

Lincoln Electric has integrated an adjustable output that offers a wide range of voltage settings, allowing users to fine-tune their settings for different materials and thicknesses. This feature, accompanied by a smooth and stable arc, contributes to high-quality welds and ease of operation.

Ease of use is further enhanced by the machine’s simple control panel, which features clear indicators and settings. Novice welders will appreciate the intuitive layout, while experienced users will value the precision controls for intricate tasks.

Another key technology utilized in the MIG-PAK 10 is Lincoln Electric’s professional-grade drive system, which ensures reliable wire feed performance. This system minimizes downtime and improves welding efficiency by reducing the chances of wire tangling or feeding issues.

Finally, the MIG-PAK 10 is constructed with durability in mind. Its robust casing is designed to withstand the rigors of welding environments, ensuring longevity and consistent performance.

In summary, the Lincoln Electric MIG-PAK 10 is a well-rounded MIG welder suitable for various welding needs. Its exceptional portability, dual wire feeding options, adjustable output, user-friendly controls, and sturdy construction make it a compelling choice for both beginners and professionals in the welding industry.