PRO1300, PRO1100e, PRO1300h/c, PRO1100, PRO1300h/c TCE, PRO1300 TCE, PRO1100e TCE

Troubleshooting

Guide (cont.)

FS: This code has the following sequence:

•When first displayed, the unit has started the defrost cycle and will reverse operation for 2 minutes. If unit is at acceptable temperature after the defrost cycle, it will go back into heating mode.

•If coolant temperature is still too low after the initial 2 minute defrost cycle, unit will shut off the compressor and run only the fan for 60 minutes. If unit is at acceptable temperature after the 60 minutes, it will go back into heating mode.

•If coolant has not reached the desired temperature after the 60 minutes, fan only mode, unit will shut down and display “FS”.

•Unit will resume normal operation after ambient temperature reaches acceptable operating temperature.

MODELS: PRO1100e TCE, PRO1300 TCE and PRO1300h/c TCE

FL3: This code means that water flow was lost. Check the system for flow obstructions.

Unit is not running (All Models):

•Check the power light. Check to see if the breaker is set.

•Make sure the filtration system is on

•Make sure the thermostat is higher than the pool water temperature

•Make sure the filter is clean and is allowing enough water to flow

•Make sure the outside ambient temperature is higher than 50ºF (38°F for h/c units)

•Make sure the 5-minute time delay has passed

FOR TCE UNITS

•Make sure time setting, in “FIL” mode, is not set to “OFF”.

Unit is running but not heating:

•Check the air coming out of the top of the unit. It should be approximately 8ºF - 15ºF lower than the surrounding ambient air temperature. If not, call AquaPRO® Systems for service.

Unit will not cool:

FOR h/c UNITS:

•Make sure P-S is set to “POL” mode as unit will not cool in “SPA” mode.

Unit runs continuously:

It may be running continuously because it cannot reach the desired temperature.

•Lower the temperature setting below the pool water temperature. Unit should turn off. If the unit is still running, call AquaPRO® Systems for service.

•A pool blanket may be required to help reach this temperature. Also, the filter pump may need to run longer for the heater to reach the desired temperature.

FOR TCE UNITS

•Make sure the setting is not set to “ON” position in the “FIL” mode.

Unit is cycling:

•Check the filters for proper water flow

•Check the evaporator coil for severe frost

•Unit could be low on refrigerant. At this point, call AquaPRO® Systems for service and turn off the power to the heater to keep the cycling from damaging the compressor.

www.aquaprosystems.com

Phone: (877)-278-2797

11

Page 12 Page 14
Page 13
Image 13
AquaPRO PRO1300h/c TCE, PRO1100e TCE, PRO1300 TCE owner manual Troubleshooting
Page 12 Page 14

PRO1100e, PRO1300 TCE, PRO1300, PRO1100, PRO1100e TCE specifications

The AquaPRO PRO1300h/c TCE, PRO1300 TCE, PRO1100e TCE, PRO1100, and PRO1100e are a series of high-performance water treatment systems designed to meet the diverse needs of residential and commercial users. These models stand out due to their advanced technology, energy efficiency, and user-friendly operation, making them ideal for various water purification tasks.

The AquaPRO PRO1300h/c TCE is equipped with advanced filtration technology that combines multiple filtration stages, ensuring the removal of contaminants, odors, and unpleasant tastes from the water. Its high-capacity system is perfect for larger households or small businesses, treating up to 1,300 gallons per day. This model features a compact design, which simplifies installation and saves valuable space, while providing a robust solution for clean drinking water.

The PRO1300 TCE model mirrors many features of the PRO1300h/c but is tailored for specific applications where heating or cooling functions are not necessary. It retains the high filtration capacity and incorporates smart technology that allows users to monitor water quality in real-time. The user-friendly interface and app connectivity offer convenient access to system status and maintenance alerts.

Moving down the range, the AquaPRO PRO1100e TCE offers slightly lower filtration capabilities but maintains the same commitment to quality and efficiency. Perfect for medium-sized households, the PRO1100e TCE boasts an eco-friendly design that minimizes energy consumption without compromising on performance. It features a smart leak detection system that alerts users in the event of any leaks, safeguarding both the unit and the property.

The PRO1100 is a more basic model intended for users seeking simplicity without sacrificing performance. It offers reliable filtration with easy-to-replace cartridges and minimal maintenance requirements, making it an excellent choice for those new to water filtration systems.

Lastly, the PRO1100e is designed for environments where energy efficiency is prioritized. Its reduced operational costs make it particularly attractive to eco-conscious consumers. With durable construction and a simple interface, these models ensure longevity and ease of use, appealing to a wide demographic.

In conclusion, the AquaPRO range encompasses various models, each with distinct features that cater to different filtration needs while ensuring high-quality performance, making the AquaPRO systems a wise investment for clean, safe water.
Top Page Image Contents