AquaPRO PRO1300h/c TCE PRO1100e TCE, and PRO1300 TCE, Electronic Temp, Controls, Selecting, Phone

Operating Instructions

		PRO1300h/c		This section allows you to run the heat	however, since the unit is checking for
				pump at set intervals during the day. If	and adding heat when needed, it
	Electronic Temp.			you have a time clock, and would like to	prevents long recovery times when
				use it please refer to the Time Clock	compared to non-TCE units. The other
	Controls			Override section.	benefit is that some states and electric
				For the TCE feature to work, your pool
					utility companies offer a discount for
	Toggling Between Heating			pump must be wired to the heat pump	off-peak usage of electricity. Please
	and Cooling Mode			See figure 7 for wiring the TCE feature	contact your electricity provider if you
	The unit will default to the heating			• This unit is prepared at the factory	have questions.
	mode. If the cooling mode is desired,			with the TCE feature installed, but	• Example of TCE operation – you require
	press the SET button until the H-C screen			set to the “off” position in the “FIL”	the system to run for 12 hours to meet
	is displayed. Then press the arrow			mode. You will need to set the	your pool filtering needs. This means for
	buttons until “COL” is displayed on the			hours of run time for the pump and	each of the 6 periods, the heater will
	screen. This puts the unit into cooling			filter system. See “activating and	run the system for 2 hours and then
	mode. The water temperature set point			setting system run time” below.	turn off for 2 hours. If the system
	will now be the water temperature that
				• The function of the TCE is done through	needed to run for 3 hours in one of the
	the unit is cooling the water to. When
					periods to reach the desired pool
	the unit is in cooling mode, the screen			a timing sequence of 6 periods per
				24 hours. You select the hours for your	temperature, the next period would be
	will flash between the current water
	temperature and “COL” to remind the			required filter pump run time, and the	1 hour on and 3 hours off unless
	user that cooling mode is activated.			heater takes care of the rest. It does this	additional heating is needed. The cycle
	Defrost Cycle			by dividing the system run time equally	continues for 6 periods and renews at
	Your AquaPRO® h/c unit is capable of			over the 6 periods, turning the pump on	the end of each 24 hours. Please call
	keeping your pool warm in very cool			for 1/6th of the specified run time and	AquaPRO® Systems at 1-877-AQUA-SYS
	temperatures. Most pool heaters will			off the remainder of the period unless	(1-877-278-2797) if you need further
	not operate below 50°F. Your h/c unit			additional heating is required. The	clarification of this feature’s operation.
	will work down to 38°F by utilizing a			heater will always operate the system	Activating and Setting System Run
	“defrost cycle”. It does this			on a daily basis for the amount of run	Time - TCE Operation
	automatically by sensing the coolant
				time you have selected. The timing	• To set the run time of the system, push
	temperature and reversing operation
				sequence begins at the initial start up.
	for 2 minutes to defrost the evaporator				the “SET” button repeatedly until “FIL”
	coil and will resume heating function			• If your pool is at or above the desired	displays. Then using the “up” and
	after defrosting the evaporator coil.			operating temperature, the heater will	“down” arrows, you can select how
				run the system the desired hours each	many total hours a day you want the
		PRO1100e TCE
				day and spread the time out evenly	system to run for your pump and
		and PRO1300 TCE		between the 6 periods. This makes for	filtration needs. The range of hours is
				better filter operation and allows the	“off” to 2, 3, 4,… up to 23 hours to
	Selecting			heater to update the water	“on”. As described before, the run time
				temperature 6 times per day.	will then be calculated and spread out
	Functionality of Unit			• If your pool needs heat, the heater will	over the 6 time periods for 24 hours.
					Selecting the “on” position will run the
	This unit is capable of operating as a Time			continue to run the system until the
					pump and filter system continuously.
	Clock Override (TCO) or as the Time Clock			desired temperature is met. If the
					The unit leaves the factory with the
	Eliminator (TCE). If you already have a			amount of run time exceeds a period’s
					“FIL” mode set to “OFF”.
	time clock on your swimming pool and			run time, the excess time will be
					Time Clock Override
	would like to maintain its normal			subtracted from the next run period(s).
	operation with the added benefit of a			Please note that on cold and / or windy	(TCO) Operation
	heat pump time clock override – please			days, the unit could run for long times		All wiring
	review the section for the Time Clock			to generate and maintain the desired
	Override. If you do not own a time clock			pool temperature. Please see the		and
					electrical connections must be performed
	for your pool system - please review the			“application” section about “pool
					by a qualified electrician. Installation
	section for the Time Clock Eliminator.			blankets” to help maintain your pool’s	must be in accordance with local and
	Time Clock Eliminator			temperature.	national codes.
				• The timing function built into the TCE	This section allows you the option of
	(TCE) Operation				using an existing time clock with the
				will always run the heat pump for
	Please read the functions of this feature			15 minutes every 4 hours to determine if	heat pump. If you do not have a time
					clock, please refer back to the Time Clock
	carefully.			more heat is needed to maintain the
					Eliminator section.
			All wiring	pool’s desired temperature - even if all
					The pump must be connected to the heat
			and	of the available run time was used in
	electrical connections must be performed				pump and also the time clock for the Time
				previous cycles. This provides a couple of
	by a qualified electrician. Installation				Clock Override feature to work correctly.
				added benefits. Pools will lose most of
	must be in accordance with local and				See figure 8 for the optional TCO wiring
	national codes.			their heat at night if left uncovered,
					schematic and electrical connections.
www.aquaprosystems.com				Phone: (877)-278-2797

6