Mineral deposits can eventually
10.Poor circuit connections at the ECO (overheat sensor) or the flue gas safety device
Ignition sparker will not operate if the electrical circuit is interrupted. Check that the connections to the ECO are secure and tighten if necessary.
11.Reset electrical power to heater
If resetting the electrical power corrected the symptom then likely the unit’s Safety Spill switch (Flue gas safety device - #33 on page 19) had tripped from a flue blockage during the previous usage. Inadequate combustion air to the room area can also cause the unit to improperly vent. Improper venting or insufficient combustion air must be corrected. Consult a licensed professional to inspect the installation.
SPARKS APPEAR AT PILOT WHEN HOT WATER TAP IS TURNED ON, BUT PILOT AND BURNERS WILL NOT IGNITE
1. Air in the Gas Line
Note: Normally this is a problem only at the time of initial installation, after the pipes have been worked on, or after a propane tank has been allowed to empty, or after the heater has been shut down for a long time.
Bleed all the air trapped in the gas line by turning the hot water faucet on and off until the air has been cleared from the line.
2. No gas to the AquaStar
A. Gas cock on gas line may not be open
B. Gas regulator may be shut or damaged. Replace or unlock the regulator. Note: The regulator furnished with the heater is exclusively designed for low gas pressure (less than ½ psig). Excessive pressure will lock it up. Locking usually happens when the gas pressure between the gas tank and the water heater’s gas regulator has not been properly regulated. See Page 2 for recommended correct gas pressure. To unlock a regulator, consult your gas supplier or a gas technician.
3. Pilot orifice clogged or gas valve is dirty
Clogging of the pilot burner can be caused by dust in the air or dirt in the gas. The pilot orifice or gas filter may need to be cleaned or replaced. See Fig. 13.
4. Water valve assembly needs to be checked
If the pilot orifice is clean, the water valve assembly should be checked. The adjustment screw on the water valve micro- switch may not be tight enough (fig. 14). Remove central cap beneath
5.Pilot electrovalve switch may need to be replaced (see fig 9).
Measure millivoltage at pilot electrovalve (see Fig 9).
6.Control Box may need to be replaced (see fig 9). Check wire connections and test operation of control box (see Fig 9).
PILOT SPARKS CONTINUOUSLY WITH NO WATER RUNNING
1. Microswitch needs adjustment
If no water is running, but pilot electrode continuously sparks, the microswitch screw to the water valve needs adjustment. See Figure 14.
PILOT LIGHTS BUT BURNERS WILL NOT COME ON
1.Confirm the flame sensor is in its proper position. see Figure 12.
2.Poor circuit connections at the flue gas safety device The burners will not come on if the powered fan exhaust is not working. Check that the unit is plugged in and that the sensors for the flue gases are secure.
3.Confirm the ECO connections are secure.
4.The Control Box may need to be replaced
(see Fig. 9).
Check wire connections and test operation of control box (see Fig 9).
5.Burner electrovalve switch may need to be replaced (see Fig. 9).
MAIN BURNERS GO OUT DURING HOT WATER USE
1. Deficient exhaustion of flue gases
Check that vent is correct and clear of any obstructions, that sensors for flue gases are secure and that electrical connection has been made. If the heater will not come back on, it will be necessary to turn the electrical supply to the heater off and then on again.
2. Flow rate diminished below activation rate
Be certain that water flow is not less than required amount to activate heater.
3. Unbalanced pressure in waterlines
The added restriction caused by the Aquastar in the hot water system can result in uneven pressures between the cold and the hot. In such cases when mixing cold water at the tap, the lower hot water pressure may be overpowered by a much higher cold water pressure, which may cause the Aquastar burners to shut down (deactivate). Make sure faucet aerators or shower heads are free of minerals. Do not add any flow restrictor to the shower head.
Typically this deactivation symptom is a result of the hot water being too hot to use comfortably. Warm inlet water generally causes this. Lowering the control knob setting and/or reducing the inlet gas supply to the heater should correct this deactivation symptom.
4.ECO (overheat sensor) tripped due to overheating Do not feed preheated water to this water heater.
5.Minimum inlet pressure on well pressure tank is inadequate
Check the inlet water pressure. For installation on a private well system with the use of a pressure tank, the lowest pressure range setting recommended is
6 720 606 601 | 17 |
