Amplifier & PSU Circuit Description
L882PB is the printed circuit board that provides the power supply and output stage amplifiers for the A85 integrated and power amplifiers.
Its function is to:
1.Drive the loudspeakers(!)
2.Provide an (always on) auxiliary 5VDC supply for the micro controller and display interface
3.Receive logic signals from the micro controller to turn on the main amplifier supply relay (mains) and connect either pair of speaker output sockets
4.Send logic signals to the micro controller pertaining to the state of the amplifiers (short circuit protection, DC offset protection, thermal protection)
5.Receive and demodulate RC5 remote style control codes via the rear panel jack and transmit them to the micro controller
6.Send a 12V trigger output via the rear panel jack for control of an auxiliary power amp when the unit is on
7.Receive a 12V trigger input from the rear jack (for use in the power amp only version)
8.Drive a pair of headphones via attenuating resistor networks The power amplifier is a symmetrical, class B, bipolar junction transistor output,
It features ‘instantaneous’ safe operating area protection in addition to sending a signal to the micro to turn off the output relays in the event of user or thermal overload. Since it is a DC- coupled design, the unit senses DC at the output and triggers the micro to turn off the loudspeaker relays in the event of excessive levels (possibly due to a faulty source component or short circuit output transistor).
The output stage uses Sanken specialised ‘audio amplifier’ power bipolar Darlington transistors which are optimised for use with this type of topology. Consequently the unit has excellent measured performance in terms of noise, slew rate, output impedance and distortion (harmonic and intermodulated) and is essentially load invariant (to a first order the measured performance is independent of the load impedance).
L882 Circuit Sheet 1
The audio input to the amplifier is connected to SK102 (which connects to the output of the preamp PCB). This signal is passed on via SK104A which forms the preamp out connection to the outside world.
SK104B provides the power amp input connection, with switch SW100 selecting between pre / power and integrated modes. The unit is wired as a preamp / power amp combination with the switch depressed, allowing the user to insert a processor or other function (e.g. graphic EQ) between the output of the preamp and the input of the power amp. With the switch in the ‘out’ position the power amp input socket is ignored and the input to the power amp is connected internally to the output of the preamp. PL100 and PL101 are ‘handbag’ links fitted to the power amp only version to connect both pairs of phono sockets in parallel for daisy chaining (as there is no preamp output on a power amp).
Relays RLY100 and RLY101 switch the two pairs of loudspeaker output sockets and are controlled by the micro lines describes above. Transistors TR100 and TR101 operate in ‘constant current sink’ mode which allow relay current to be approximately constant although the main power supply rails will vary with mains input and load conditions. The current is around 20mA per relay.
Star point SP100 is the ground ‘mecca’ for the entire amplifier (comprising all three PCBs within the unit). All of the separately named grounds are joined explicitly at this point. Different named grounds are used to ensure that no two ‘different’ grounds share copper, which could compromise the noise, distortion or crosstalk performance of the amplifier.
The loudspeaker output signals are passed to socket SK106 which connects to SK107 and onto the headphone output via the attenuation resistors R103 thru R106.
The hierarchy containing the other sheets is self explanatory. Each of the port names shown on the top sheet connects to the port of the same name on the lower sheets.
L882 Circuit Sheet 2
This sheet contains the power supplies, the rear panel jack socket trigger circuits, the standby relay control and the ‘interface’ circuits between the output signals of the power amplifiers and the inputs expected by the micro processor.
The mains input enters the unit at SK203, with capacitors C205 and C206 acting as conducted RF suppression. The earth connection is passed on to the chassis (for safety reasons the chassis metalwork remains connected to mains power earth at all times). Switch SW200 is the voltage selector switch, allowing the unit to be operated in 230V or 115V mains countries by switching the
Relay RLY200 switches the primary side of the mains transformer, allowing the micro to control the on / off status of the amplifier. Its contacts are snubbed by capacitors C207 and C208 (to eliminate switching spark transients and prolong relay lifespan). The primary windings of the toroidal mains transformer connect to SK204.
PCB mounted transformer TX200 is powered all the time that mains is present on SK203, irrespective of the on / off status of the amplifier. This is to ensure that the micro processor is always operational and can thus control the mains switching for the main amplifier. Secondary fuse F202 limits the current in the event of a failure mode, as the short circuit primary current of TX200 would be insufficient to blow the mains fuses.
Diodes D200 thru D203, C227 and IC201 provide the 5VDC supply which powers the micro and display PCB and the relay coils. C224 is to reduce diode noise being transmitted back through the leakage capacitance of TX200.
The mains transformer secondary winding is connected to SK200. This is a centre tapped winding, and is used with full bridge rectifier BR200 to produce the main positive and negative supplies for the power amp. C209 and C210 are the large reservoir capacitors, with C211 and C212 acting as high frequency decouplers. The main power supply rails and ground are accessible on SK205 for future module expansion.
The circuitry around SK201A and IC200 is to receive and demodulate remote control commands sent in via the rear panel jack socket. This is for
L200 and C200 form a parallel resonant circuit at approximately 37kHz. The output from this bandpass filter is passed into IC200A where it is ‘chopped’ and fed to IC200B to provide the output signal.
