Arcam T32 manual Presets, iPod operation, Aux input, English

Presets

The T32 can store up to a total of 100 presets. A preset is a combination of band and frequency, or a DAB or Sirius channel (where fitted), stored in a numbered location. Fourteen of these may be accessed directly from the dedicated front panel preset buttons, although all 100 presets can be stored and retrieved using the Control knob or remote control.

Storing a preset

First select the radio station you wish to assign to a preset. Press Store on the front panel or remote and the T32 displays the lowest numbered vacant preset, for example:

Preset 07

Preset empty

Press OK to store the station to location 07.

Alternatively, you can use any of the dedicated preset buttons, the front panel Control knob, or Dor Eon the remote control, to select a different preset. Press OK to confirm that you want to store the station at this preset location. The display shows, for example:

Preset 42

Preset stored

If you select a preset that is already used, the previously stored station is replaced.

Selecting a preset

To select a stored preset:

<Press one of the dedicated front panel preset buttons briefly (for presets 1 to 7). Press and hold to access the higher numbers (for presets 8 to 14).

<Use the numeric keypad on the remote control to enter the preset number.

<Press PRESET on the front panel (or P/TUNE on the remote) and use the control knob (or Dand E on the remote control) to select a used preset from

1to 100.

<Press Cor Bto select a used preset from 1 to

Preset 05

FM 98.50MHz

Press Oon the remote control or OK on the front panel within the time-out period to output the selected station.

iPod operation

If an rDock is connected to the T32, it automatically enables ‘iPod mode’.

To use an rLead, you must set this mode explicitly. Press MENU (or Uon the remote) and navigate to ‘External input’ by pressing 5or 6on the front panel and use the Control knob (or Eon the remote), to select:

External input

iPod mode Enabled

Select the iPod as a source by pressing 5or 6on the front panel (or Mon the remote control) until ‘iPod’ is shown on top line of the display:

iPod

Initialising...

If the rDock or rLead does not have an iPod attached at this point, you are reminded that one needs to be connected (or reconnected):

iPod

Connect iPod

Navigation

With an iPod connected, the screen changes to:

Music	è è
Make	Selection

Navigate through the different ways of selecting tracks on your iPod (the actual categories will depend on your iPod model) by pressing Cand Bon the remote, confirming your selection withO.

���������

�������

������

�����

��������

������

���������

����������

For example, if you start your track selection from ‘Artists’, you can cycle through the list of Artists using Cor Bon the remote, selecting one with O.

Choose an ‘Album’ from that Artist using Cor Bon the remote (if there is more than one Album), selecting one with O.

In the same way, choose a ‘Song’ (i.e. track) from that Album using Cor Bon the remote (if there is more than one Song), selecting one with O.

��������

��������

��������

�������

�������

�������

������

������

To change a Song being played, press Oand use the same method to navigate back to a new Song, Album or Artist.

Shuffle and Repeat modes

You can apply ‘Shuffle’ mode (for random playback of tracks) by pressing S on the remote.

Set ‘Repeat mode’ by pressing Ron the remote.

Aux input

The analogue auxiliary input on T32 is intended primarily for use with Arcam’s rDock and rLead accessories.

If you are not using the auxiliary input for iPod connectivity, you may use the Aux in socket as a standard analogue line level input.

To do this, press Uand navigate to ‘External input’ and use the Control knob (Cor Bon the remote), to select:

External input

Input labelled AUX

.

English

E-13