Roller should be 1/2 – 7/8 in. (12.7 –
22.2mm) from the frame when the attachment clutch is engaged.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Figure 25 |
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| OS8080 | |||||||||||||||
Adjust the Attachment Clutch Cable Spring Extension
(Figure 26)
1.Check the attachment clutch cable spring extension.
Measure the length of the attachment clutch cable spring with the clutch lever disengaged.
Then measure the attachment clutch spring with the clutch lever engaged. The spring should be 1/2 – 9/16 in. (12.7
– 14.3 mm) longer when the clutch lever is engaged.
•If spring extension is within the specified range, go to Check Attachment Brake on page 25.
•If spring extension is outside of specified range, go to step 2.
1/2 – 9/16 in. (12.7 – 14.3 mm)
Figure 26 | OS8085 |
2.Adjust cable length (Figure 26).
a.Loosen jam nut on cable.
b.To increase spring extension, adjust barrel down the cable and tighten jam nut.
c.To decrease spring extension, adjust barrel up the cable and tighten jam nut.
Check Attachment Brake
(Figure 27)
1.With the clutch lever disengaged, brake pad must contact attachment belt. With clutch lever engaged, brake pad must be more than 1/16 in. (1.6 mm) from belt. If there is more than 1/16 in. (1.6 mm) gap, go to Check Belt Finger Clearance on page 26. If there is less than 1/16 in. (1.6 mm) gap, go to Step 2.
Minimum of 1/16 in. (1.6 mm)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||||||
1. | Brake Arm and Pad |
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||
2. | Attachment Pulley |
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||||
Figure 27 | OS8092 |
2.If there is less than 1/16 in. (1.6 mm) gap between brake pad and belt, follow these steps:
a.To increase brake pad gap, loosen idler adjustment nut, and move idler away from belt. Position idler to achieve a 1/16 in. (1.6 mm) minimum brake pad gap and a 1/2 – 7/8 in. (12.7 – 22.2 mm) gap between the plastic roller and the frame.
b.Check the clutch cable spring extension and adjust as necessary to achieve a 1/2 – 9/16 in. (12.7 – 14.3 mm) spring extension.
c.If the cable needed adjustment, recheck gaps described in step 1. Repeat steps as necessary until brake clearance, roller gap and spring extension are within specified ranges.
IMPORTANT: If adjustments cannot be brought into specified ranges see your dealer for repairs.
GB - 25