TO ADJUST AUGER CONTROL CABLE | TO ADJUST IDLER POSITION | ||
WARNING: IMPROPER ADJUSTMENT | The idler must be as close as possible to the drive belt | ||
when the auger clutch is disengaged, but not so close | |||
could result in death or serious injury. AUGER | that it causes auger rotation. | ||
BRAKE MUST DISENGAGE when clutch is | |||
|
| ||
engaged. BRAKE MUST STOP AUGER |
| WARNING: ROTATING PARTS can cut off | |
WITHIN 5 SECONDS of releasing auger |
| body parts. Keep hands and feet away. Loose | |
clutch bail. |
| ||
| clothing, long hair or scarves can get caught | ||
|
| ||
There must ALWAYS be some slight noticeable slack in |
| in rotating parts and cause death or serious | |
| injury. | ||
the auger control cable when the auger is disengaged. |
|
| |
This allows Extension Spring to pull idler Arm/Brake, | To adjust the idler position: | ||
which applies the brake to the Belt. | |||
IMPORTANT: If adjustment cannot be achieved, the | |||
The auger clutch bail should travel | |||
Drive Belt must be replaced. | |||
1. | Shut off engine, allow to cool, and remove cowl. | ||
A properly adjusted clutch must extend control cable | |||
2. | Ensure control cable has some slight, noticeable | ||
Spring approximately 1/4 to 3/8” | |||
| slack when auger clutch is disengaged (bail in | ||
clutch bail contacts handlebar. |
| ||
| lowered position). | ||
|
| ||
1. Shut off engine. | 3. | Ensure belt fingers are properly adjusted. See To | |
2. Loosen locknut on threaded section of control |
| Adjust Belt Finger. | |
cable adjusting feature. | 4. | Loosen idler hardware, reposition idler along slot in | |
3. Turn solid section to provide some slight, |
| idler arm, and tighten hardware. | |
noticeable slack in cable. | 5. | Check for proper extension of control cable spring. | |
4. Hold the solid section with a pliers and gently, with |
| See To Adjust Auger Control Cable. | |
a small wrench, tighten the locknut. | 6. | Start engine and ensure auger does not rotate | |
IMPORTANT: If there is still no resistance, the idler |
| when auger clutch is disengaged. | |
7. | Shut off engine. | ||
position must be adjusted. See To Adjust Idler Position. | |||
8. | Repeat the above steps until proper adjustment is | ||
| |||
1/4- 3/8"to 3/8” |
| achieved. | |
9. | Replace cowl. | ||
|
|
|
|
|
|
|
|
| |
|
|
| 1 |
|
| 3 | |
|
|
|
|
| 4 | ||
|
|
|
|
| 1 | ||
|
|
|
|
| 2 | 5 | |
|
|
|
|
|
| ||
|
|
| 2 |
|
|
|
|
|
|
| 4 |
|
|
| 5 (3HP) |
|
|
|
|
|
|
| |
|
| 3 | 5 |
|
|
|
|
1. | Control Cable | 3. | Locknut |
|
|
|
|
| Spring | 4. | Threaded Section |
|
|
|
|
2. | Adjusting Feature | 5. | Solid Section |
|
|
|
|
|
|
|
| 1. | Idler Arm/Brake |
| |
|
|
| OS1220 | 2. | Idler |
|
|
|
|
|
|
|
| ||
|
|
|
| 3. | Slot |
|
|
|
|
|
| 4. | Auger Clutch |
| |
|
|
|
|
| Control Cable |
| |
|
|
|
| 5. | Belt Fingers | OS0053 | |
|
|
| GB - 15 |
|
|
|
|