ASRock SLIBridge3S Card | ASRock Fatal1ty X79 Professional manual

Step2. If required, connect the auxiliary power source to the PCI Express graph- ics cards.

Step3. Align and insert the ASRock SLI_Bridge_3S Card to the goldﬁngers on each graphics card. Make sure the ASRock SLI_Bridge_3S Card is ﬁrmly in place.

ASRock SLI_Bridge_3S Card

Step4. Connect a VGA cable or a DVI cable to the monitor connector or the DVI connector of the graphics card that is inserted to PCIE1 slot.

25

Image 25

ASRock Fatal1ty X79 Professional manual ASRock SLIBridge3S Card

Contents

Fatal1ty X79 Professional Series Fatal1ty Story LIVIN’ Large Disclaimer Copyright Notice Contents Uefi Setup Utility Introduction Package Contents Specifications Smart Switch ConnectorUSB3.0 Unique Feature Bios FeatureSupport CD HardwarePage Page Page 24.4cm 9.6 Motherboard Layout Table for Audio Output Connection LAN Port LED IndicationsPage Screw Holes Pre-installation Precautions CPU Installation Locate Pin1 and the two orientation key notches Installation of CPU Fan and Heatsink Installing a Dimm Installation of Memory Modules Dimm Pcie Slot Conﬁgurations Expansion Slots PCI and PCI Express Slots Installing an expansion card Requirements ASRock SLIBridge3S Card Two Goldﬁngers Installing Three SLITM-Ready Graphics Cards Installing Four SLITM-Ready Graphics Cards For Windows XP / XP 64-bit OS For Slitm mode only Driver Installation and Setup Select Nvidia Control Panel tab Follow steps a to E on Page CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards Installing Four CrossFireXTM-Ready Graphics Cards For Windows 7 / VistaTM OS For Windows XP OS \ Surround Display Information Surround Display Feature CIR sensors in different angles ASRock Smart Remote Installation Guide ASRock XFast Charger Operation Guide Description Jumpers Setup Serial ATA3 Connectors Onboard Headers and Connectors USB 2.0 Headers Besides six default USB Consumer Infrared Module Header This header can be used to Chassis Speaker Header Please connect the chassis CPU Fan Connectors Please connect the CPU fan Port on the I/O panel, there Installation Guide of Rear USB 3.0 Bracket Installation Guide of Front USB 3.0 Panel Smart Switches Status Code Description 15 Dr. DebugPage Page Page Serial ATA3 SATA3 Hard Disks Installation Serial ATA Sata / Serial ATA2 SATA2 Hard Disks Installation What is Hot Swap Function? What is Hot Plug Function?Hot Plug and Hot Swap Functions for Sata / SATA2 HDDs Hot Plug and Hot Swap Functions for SATA3 HDDs Points of attention, before you process the Hot Plug How to Hot Plug a Sata / SATA2 / SATA3 HDD Set up Uefi Driver Installation GuideUse RAID Installation Guide to set RAID conﬁguration Install Windows XP / XP 64-bit OS on your system Installing Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Uefi Menu Bar Introduction Main Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Browser OC Tweaker Screen Dram Timing Control Load XMP Setting Turbo Boost Power LimitCore Current Limit Additional Turbo Voltage Dram Power Down Mode Command RateDram tRP Dram tRAS Memory Mode Memory Power Savings ModeChannel Interleaving Rank Interleaving User Defaults Load Power Saving ModeCPU PLL Voltage PCH 1.1V Voltage Instant Flash Advanced Screen CPU Configuration Enhance Halt State C1E CPU Thermal ThrottlingCPU C3 State Support CPU C6 State Support North Bridge Configuration South Bridge Configuration Onboard Debug Port LED Good Night LED Storage Configuration Hard Disk S.M.A.R.T Serial Port Super IO ConfigurationSerial Port Address Infrared Port Acpi Configuration USB Configuration Intel ME Subsystem Conﬁguration ME Version ME Subsystem Hardware Health Event Monitoring Screen Boot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Windows VistaTM 64-bit Page Windows 7 64-bit