Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus CUV266-DLS TIP:, NOTES:, 3)Primary (Blue) / Secondary IDE Connectors (40-1pin IDE1/IDE2)

1 92

Download 92 pages, 3.26 Mb

.3 H/WConnectors SETUP

3.HARDWARE SETUP

3)Primary (Blue) / Secondary IDE Connectors (40-1 pin IDE1/IDE2)

These connectors support the provided UltraDMA/100/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA/100/66 slave device (hard disk drive) and the black connector to the UltraDMA/100/66 master device. It is recommended that non-UltraDMA/100/66 devices be connected to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup (see 4.6. Boot Menu). If you have more than two UltraDMA/100/66 devices, purchase another UltraDMA/100/66 cable.

NOTES:

1.Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector. This prevents incorrect orientation when you connect the cables.

2.The hole near the blue connector on the UltraDMA/100/66 cable is intended likewise.

TIP: You may configure two hard disks to be both Masters with two ribbon cables – one for the primary IDE connector and another for the secondary IDE connector.

IMPORTANT: For UltraDMA/100/66 IDE devices,use a 40-pin 80-conductor IDE cable. The UltraDMA/66 cable included in the motherboard package also supports UltraDMA/100.

1

1

NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.

Primary IDE Connector

PIN 1

CUV266-DLS

Secondary IDE Connector

CUV266-DLS IDE Connectors

34	ASUS CUV266-DLS User’s Manual

Contents

JumperFree™ DDR SDRAM 133MHz FSB AGP Pro/4X Product Name: ASUS CUV266-DLS Manual Revision: 1.01 E788 Release Date: ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) 3.7.1 Installing an Expansion Card 3.7.2 Assigning IRQs for Expansion Cards 3.7.3 Accelerated Graphics Port (AGP) Pro Slot 4.1.1 Upon First Use of the Computer System 4.3.1 Primary & Secondary Master/Slave 4.4.2 I/O Device Configuration 5.1.1 Windows 98/2000/ME First Time Installation CUV266-DLSMotherboard Support CD Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help 1.1How This Manual Is Organized 1.2 Item Checklist 2.1ASUS CUV266-DLSMotherboard 2.1.1 Specifications AGP Pro Slot: Wake-On-Ring: SMBus: PCI Expansion Slots: Smart BIOS: 2.1.2Performance 2.1.3Intelligence 2.2Motherboard Components 2.2.1Component Locations 3.1Motherboard Layout 3.2Layout Contents 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Frequency Settings (DIP Switches) 1) JumperFree™ Mode (JEN) 4.4 Advanced Menu Setting JEN 2)CPU External Frequency Selection (DIP_F Switches 1–5) NOTES: 4)Keyboard Wake-up (3-pinKB_PWR) DISABLED 5)Clear RTC RAM (CLRTC) 6)LAN Enable/Disable Jumper (3-pinLAN_EN) 7)SCSI Enable/Disable Jumper (3-pinSCSI_EN) Page 3.5System Memory 3.5.1 DDR SDRAM Notes 3.5.2Memory Installation 3.6Central Processing Unit (CPU) 3.6.1CPU Installation 3.7Expansion Cards 3.7.1 Installing an Expansion Card 3.7.2Assigning IRQs for Expansion Cards Standard Interrupt Assignments Interrupt Request Table for this Motherboard 3.7.3Accelerated Graphics Port (AGP) Pro Slot Page 3.8Connectors 3.8.1 External Connectors 4)Parallel Port (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) NOTE: Serial printers must be connected to the serial port 5)Serial Ports (Teal/Turquoise 9-pinCOM1 / 9-pinCOM2) 3.8.2Internal Connectors 3)Primary (Blue) / Secondary IDE Connectors (40-1pin IDE1/IDE2) TIP: 4)Wake-On-LANConnector (3-pinWOL_CON) 5)Wake-On-RingConnector (2-pinWOR) ATX power supply with at least 720mA +5V standby power SCSI Connection Notes Page These are not jumpers, do not place jumper caps over these connectors 8)USB Headers (10-1pin USB2_3, USB4_5) 9)Infrared Module Connector (5-pinIR) UART2 Use Infrared 4.4.2 I/O Device Configuration) 10)Chassis Open Alarm Lead (4-1pin CHASSIS) IMPORTANT: Make sure that the ATX 12V power supply (minimum 12)SMBus Connector (5-1pin SMB_CON) 13)ASUS iPanel Connector (24-1pin AFPANEL) module to the SIR connector The following 20-pinPANEL illustration is for items 14)System Power LED Lead (3-1pin PWR.LED) 15)System Warning Speaker Lead (4-pinSPEAKER) 16)System Message LED Lead (2-pinMSG.LED) 17)System Management Interrupt Lead (2-pinSMI) 3.9Starting Up the First Time Award BIOS Beep Codes Page 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 1. Save Current BIOS to File Save Current BIOS To File A:\XXX-XX.XXX SETUP BIOS 4.1.2Updating BIOS Procedures Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Type Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] This field displays the BIOS language version Supervisor Password [Disabled] / User Password [Disabled] A Note about Passwords Forgot the Password 4.4Advanced Menu BIOS Update [Enabled] PS/2 Mouse Function Control [Auto] USB Legacy Support [Auto] OS/2 Onboard Memory > 64M [Disabled] 4.4.1Chip Configuration Bank Interleave [Auto] Configuration options: [None] [2 Banks] [4 Banks] [Auto] DDR_1T/2T_ITEM [2T CMD] Configuration options: [1T CMD] [2T CMD] [Auto Mode] SDRAM Data Integrity Mode [Non-ECC] Video Memory Cache Mode [UC] Onboard PCI IDE Enable [Both] Memory Hole At 15M-16M[Disabled] 4.4.2I/O Device Configuration Onboard Parallel Port [378H/IRQ7] Parallel Port Mode [ECP+EPP] ECP DMA Select [3] ECP Parallel Port Mode 4.4.3PCI Configuration PCI IRQ Resource Exclusion 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend Mode [Disabled] PWR Button < 4 Secs [Soft Off] 4.5.1Power Up Control 4.5.2 Hardware Monitor 4.6Boot Menu Boot Sequence Menu Boot Plug & Play O/S [No] MPS 1.4 Support [Enabled] Boot Virus Detection [Disabled] Quick Power On Self Test [Enabled] 4.7Exit Menu Exit Saving Changes Discard Changes Save Changes 5.1Operating Systems 5.1.1 Windows 98/2000/ME First Time Installation 5.2 CUV266-DLSMotherboard Support CD 5.2.1 Installation Menus 5.2.2Applications Cyberlink Video and Audio Applications: •ASUS Screen Saver: Installs the ASUS screen saver Show Motherboard Information: •Browse Support CD: Allows you to view the contents of the support CD ReadMe: Page 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe Settings History Fan Control Information Hard Drives Memory Device Summary DMI Explorer Utility Execute Program 6.1.3ASUS PC Probe Task Bar Icon Page 7.1 Glossary APPENDIX Boot Bus Master IDE Byte (Binary Term) COM Port LPT Port (Line Printer Port) MMX (Klamath) CPU as well as other OnNow PC100 ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions)