Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus CUV266-DLS 8)USB Headers (10-1pin USB2_3, USB4_5), These are not jumpers, do not place jumper caps over these connectors

1 92

Download 92 pages, 3.26 Mb

.3 H/WConnectors SETUP

3.HARDWARE SETUP

7)CPU Fan and Chassis Fan Connectors (CPU1_FAN, CPU2_FAN, CHA_FAN)

The three fan connectors support cooling fans of 350mA (4.2 Watts) or less. Orient the fans such that it blows air across the onboard heat sinks instead of the expansion slots. The fan wiring and plug may vary depending on the fan manufacturer. Connect the fan cable to the connector making sure that the black wire matches the ground pin. (NOTE: The “Rotation” signal should be used accordingly for a specially designed fan with a rotation signal. You can monitor the Rotations Per Minute (RPM) using ASUS PC Probe (see 6. SOFTWARE REFERENCE).

WARNING! Make sure to connect the fan cables to the fan connectors. Lack of sufficient airflow within the system could cause damage to the motherboard.

These are not jumpers, do not place jumper caps over these connectors!

	GND	CPU2_FAN
	+12V	CPU2_FAN
1	Rotation
	CPU1_FAN
	GND
	+12V
	Rotation
CUV266-DLS	CHA_FAN
CUV266-DLS 12-Volt	Rotation +12V GND
Cooling Fans

8)USB Headers (10-1 pin USB2_3, USB4_5)

If the USB port connectors on the back panel are inadequate, two USB headers are available for four additional USB port connectors. Connect a 2-port USB connector set to a USB header and mount the USB bracket to an open slot in the chassis.

	USB2_3
	USBP3+ GND	–USBP3	Power USB		USB4_5
	USBP3+ GND	–USBP3	Power USB		USBP5+ GND	–USBP5	PowerUSB
	10		6
	5		1	10			6
	GND NC	–USBP2	PowerUSB	10			6
	GND NC				USBP4+ GND NC	–USBP4	PowerUSB
CUV266-DLS	USBP2+				USBP4+ GND NC	–USBP4	PowerUSB
				5			1

CUV266-DLS Front Panel USB Header

38	ASUS CUV266-DLS User’s Manual

Contents

JumperFree™ DDR SDRAM 133MHz FSB AGP Pro/4X Product Name: ASUS CUV266-DLS Manual Revision: 1.01 E788 Release Date: ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) 3.7.1 Installing an Expansion Card 3.7.2 Assigning IRQs for Expansion Cards 3.7.3 Accelerated Graphics Port (AGP) Pro Slot 4.1.1 Upon First Use of the Computer System 4.3.1 Primary & Secondary Master/Slave 4.4.2 I/O Device Configuration 5.1.1 Windows 98/2000/ME First Time Installation CUV266-DLSMotherboard Support CD Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help 1.1How This Manual Is Organized 1.2 Item Checklist 2.1ASUS CUV266-DLSMotherboard 2.1.1 Specifications AGP Pro Slot: Wake-On-Ring: SMBus: PCI Expansion Slots: Smart BIOS: 2.1.2Performance 2.1.3Intelligence 2.2Motherboard Components 2.2.1Component Locations 3.1Motherboard Layout 3.2Layout Contents 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Frequency Settings (DIP Switches) 1) JumperFree™ Mode (JEN) 4.4 Advanced Menu Setting JEN 2)CPU External Frequency Selection (DIP_F Switches 1–5) NOTES: 4)Keyboard Wake-up (3-pinKB_PWR) DISABLED 5)Clear RTC RAM (CLRTC) 6)LAN Enable/Disable Jumper (3-pinLAN_EN) 7)SCSI Enable/Disable Jumper (3-pinSCSI_EN) Page 3.5System Memory 3.5.1 DDR SDRAM Notes 3.5.2Memory Installation 3.6Central Processing Unit (CPU) 3.6.1CPU Installation 3.7Expansion Cards 3.7.1 Installing an Expansion Card 3.7.2Assigning IRQs for Expansion Cards Standard Interrupt Assignments Interrupt Request Table for this Motherboard 3.7.3Accelerated Graphics Port (AGP) Pro Slot Page 3.8Connectors 3.8.1 External Connectors 4)Parallel Port (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) NOTE: Serial printers must be connected to the serial port 5)Serial Ports (Teal/Turquoise 9-pinCOM1 / 9-pinCOM2) 3.8.2Internal Connectors 3)Primary (Blue) / Secondary IDE Connectors (40-1pin IDE1/IDE2) TIP: 4)Wake-On-LANConnector (3-pinWOL_CON) 5)Wake-On-RingConnector (2-pinWOR) ATX power supply with at least 720mA +5V standby power SCSI Connection Notes Page These are not jumpers, do not place jumper caps over these connectors 8)USB Headers (10-1pin USB2_3, USB4_5) 9)Infrared Module Connector (5-pinIR) UART2 Use Infrared 4.4.2 I/O Device Configuration) 10)Chassis Open Alarm Lead (4-1pin CHASSIS) IMPORTANT: Make sure that the ATX 12V power supply (minimum 12)SMBus Connector (5-1pin SMB_CON) 13)ASUS iPanel Connector (24-1pin AFPANEL) module to the SIR connector The following 20-pinPANEL illustration is for items 14)System Power LED Lead (3-1pin PWR.LED) 15)System Warning Speaker Lead (4-pinSPEAKER) 16)System Message LED Lead (2-pinMSG.LED) 17)System Management Interrupt Lead (2-pinSMI) 3.9Starting Up the First Time Award BIOS Beep Codes Page 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 1. Save Current BIOS to File Save Current BIOS To File A:\XXX-XX.XXX SETUP BIOS 4.1.2Updating BIOS Procedures Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Type Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Language [English] This field displays the BIOS language version Supervisor Password [Disabled] / User Password [Disabled] A Note about Passwords Forgot the Password 4.4Advanced Menu BIOS Update [Enabled] PS/2 Mouse Function Control [Auto] USB Legacy Support [Auto] OS/2 Onboard Memory > 64M [Disabled] 4.4.1Chip Configuration Bank Interleave [Auto] Configuration options: [None] [2 Banks] [4 Banks] [Auto] DDR_1T/2T_ITEM [2T CMD] Configuration options: [1T CMD] [2T CMD] [Auto Mode] SDRAM Data Integrity Mode [Non-ECC] Video Memory Cache Mode [UC] Onboard PCI IDE Enable [Both] Memory Hole At 15M-16M[Disabled] 4.4.2I/O Device Configuration Onboard Parallel Port [378H/IRQ7] Parallel Port Mode [ECP+EPP] ECP DMA Select [3] ECP Parallel Port Mode 4.4.3PCI Configuration PCI IRQ Resource Exclusion 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend Mode [Disabled] PWR Button < 4 Secs [Soft Off] 4.5.1Power Up Control 4.5.2 Hardware Monitor 4.6Boot Menu Boot Sequence Menu Boot Plug & Play O/S [No] MPS 1.4 Support [Enabled] Boot Virus Detection [Disabled] Quick Power On Self Test [Enabled] 4.7Exit Menu Exit Saving Changes Discard Changes Save Changes 5.1Operating Systems 5.1.1 Windows 98/2000/ME First Time Installation 5.2 CUV266-DLSMotherboard Support CD 5.2.1 Installation Menus 5.2.2Applications Cyberlink Video and Audio Applications: •ASUS Screen Saver: Installs the ASUS screen saver Show Motherboard Information: •Browse Support CD: Allows you to view the contents of the support CD ReadMe: Page 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe Settings History Fan Control Information Hard Drives Memory Device Summary DMI Explorer Utility Execute Program 6.1.3ASUS PC Probe Task Bar Icon Page 7.1 Glossary APPENDIX Boot Bus Master IDE Byte (Binary Term) COM Port LPT Port (Line Printer Port) MMX (Klamath) CPU as well as other OnNow PC100 ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions)