11.eSATA port. This port connects to an external Serial ATA hard disk drive.

12.DVI-I port. This port is for any DVI-I compatible device and are HDCP compliant, allowing playback of HD DVD, Blu-Ray and other protected content.

13.HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector, and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected content.

14.USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0/1.1 devices.

1.7.2Internal connectors

1.ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)

These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

ATX12V EATXPWR

E35M1-I DELUXE

 

 

 

PIN 1

 

 

 

 

 

 

 

 

 

+12V DC

 

 

 

 

 

GND

+3 Volts

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

+12

Volts

 

 

 

 

 

 

+5 Volts

+12V DC

 

 

 

 

GND

+12

Volts

 

 

 

 

 

 

+5 Volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+5V Standby

 

 

 

 

 

 

+5 Volts

 

 

 

 

 

 

 

 

Power OK

 

 

 

 

 

 

-5 Volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+5 Volts

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+5 Volts

 

 

 

 

 

 

PSON#

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GND

 

 

 

 

 

 

GND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+3

Volts

 

 

 

 

 

 

-12 Volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+3

Volts

 

 

 

 

 

 

+3 Volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PIN 1

E45M1-I DELUXE ATX power connectors

For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 350 W.

DO NOT forget to connect the 4-pin ATX +12V power plug. Otherwise, the system will not boot up.

We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate.

If you are uncertain about the minimum power supply requirement for your system, refer to the Recommended Power Supply Wattage Calculator at http://support.asus. com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.

Chapter 1: Product introduction

1-11