Asus P/E-P55T2P4D manual

P/E-P55T2P4D Motherboard

USER'S MANUAL

Contents

Page USER'S NOTICE © Copyright 1996 ASUSTeK Computer Inc. All rights reserved Product Name: P/E-P55T2P4D Product Rev: Manual Rev: Page CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE V. DESKTOP MANAGEMENT VI. PCI-SC200SCSI Card FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this manual is organized Item Checklist Features of This Motherboard Parts of the Motherboard Map of the Motherboard Jumpers Expansion Slots Connectors Installation Steps 1. Jumpers Jumper Settings 3-5.Processor Type III.INSTALLATION 3.Voltage Type (JP9, 10, 11, 12, 17) 4. Vcore (JP5, 6, 7, 8, 19, 20, 21) 5. Vio (JP2, 3) 6.CPU to BUS Frequency Ratio (JP15 & 16) 7.CPU External (BUS) Frequency Selection (JP29 & 30) Set the above jumpers by the Internal speed of the Intel CPU as follows: Internal Ratio 8.APIC Dual CPU Selection (JP18) Dual CPU JP18 Enable Disable 9.Flash ROM Boot Block Programming (JP32) Programming JP32 Disabled Enabled 10.CMOS RAM (JP34) 11.PCI Slot 1 Mode Selection (JP37, 38) Slave PCI JP38 JP37 2.System Memory (DRAM & SRAM) DRAM Installation Procedures: Static RAM (SRAM) for Level 2 (External) Cache Compatible Cache Modules for this Motherboard 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ASUS MediaBus Card 5.External Connectors 3.Parallel Printer Connector (26 Pin Block) Note 4.Serial port COM1 and COM2 connectors (Two 10-pinblocks) 5.Floppy drive connector (34-pinblock ) 6.Primary / Secondary IDE connectors (Two 40-pinBlock) 7.Board Power Input (12-pinblock) 8.IDE activity LED 9.Turbo LED lead (CON3) 10.SMI suspend switch lead (CON3) 11.Reset switch lead (CON3) 12.Keyboard lock switch lead (CON3) 13.Speaker connector (CON3) Power Connection Procedures 6. BIOS Setup Standard CMOS Setup Details of Standard CMOS Setup: For an IDE hard disk drives, you can: •Use theAuto setting for detection during bootup (see below) •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup (New Feature) Drive A, Drive B Floppy 3 Mode Support Video Halt On This field determines which types of errors will cause the system to halt BIOS Features Setup Details of BIOS Features Setup: (BIOS CPU Internal Cache / External Cache Enable Disable Quick Power On Self Test Typematic Rate (Char/Sec) Typematic Delay (Msec) 250ms Security Option System Chipset Features Setup [DRAM and ECC] DRAM are 72 bits wide Memory parity SERR# (NMI): DRAM ECC/PARITY Select: DRAM are 64 (not 72) bits wide (Chipset Onboard Parallel Port 3BCH / IRQ 7 378H / IRQ , 278H / IRQ 5, Disabled Power Management Setup Details of Power Management Setup: (Power Video Off Option Susp Stby Off PNP and PCI Setup & (Plug IRQ xx Used By ISA No/ECU Yes IRQ10 Used By ISA Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save and Exit Setup Exit Without Saving Flash Memory Writer Utility The Flash Memory Writer Utility Screen: 1. Save Current BIOS to File 2. Update BIOS Main Block from File Boot Block of New BIOS is different from old one Please Use 'Advanced Feature' to flash whole bios 3. Advanced Features DO NOT TURN OFF THE SYSTEM IF THERE IS A PROBLEM then turn off your system Desktop Management Interface (DMI) Introducing the DMI utility System Requirements Using the DMI utility Notes: Save MIFD Load MIFD Load BIOS Defaults (This page was intentionally left blank) NCR SCSI BIOS and Drivers The PCI-SC200SCSI Interface Card Setting Up the PCI-SC200 Setting the INT Assignment Terminator Settings ID (SCSI PCI only must both