Contents
Page
USER'S NOTICE
© Copyright 1996 ASUSTeK Computer Inc. All rights reserved
Product Name: P/E-P55T2P4D
Product Rev:
Manual Rev:
Page
CONTENTS
I. INTRODUCTION
II. FEATURES
III. INSTALLATION
IV. BIOS SOFTWARE
V. DESKTOP MANAGEMENT
VI. PCI-SC200SCSI Card
FCC & DOC COMPLIANCE
Federal Communications Commission Statement
•This device may not cause harmful interference, and
•Re-orientor relocate the receiving antenna
•Increase the separation between the equipment and receiver
How this manual is organized
Item Checklist
Features of This Motherboard
Parts of the Motherboard
Map of the Motherboard
Jumpers
Expansion Slots
Connectors
Installation Steps
1. Jumpers
Jumper Settings
3-5.Processor Type
III.INSTALLATION
3.Voltage Type (JP9, 10, 11, 12, 17)
4. Vcore (JP5, 6, 7, 8, 19, 20, 21)
5. Vio (JP2, 3)
6.CPU to BUS Frequency Ratio (JP15 & 16)
7.CPU External (BUS) Frequency Selection (JP29 & 30)
Set the above jumpers by the Internal speed of the Intel CPU as follows:
Internal
Ratio
8.APIC Dual CPU Selection (JP18)
Dual CPU JP18
Enable
Disable
9.Flash ROM Boot Block Programming (JP32)
Programming JP32
Disabled
Enabled
10.CMOS RAM (JP34)
11.PCI Slot 1 Mode Selection (JP37, 38)
Slave
PCI
JP38
JP37
2.System Memory (DRAM & SRAM)
DRAM Installation Procedures:
Static RAM (SRAM) for Level 2 (External) Cache
Compatible Cache Modules for this Motherboard
3.Central Processing Unit (CPU)
4.Expansion Cards
Expansion Card Installation Procedure:
Assigning IRQs for Expansion Cards
Assigning DMA Channels for ISA Cards
ASUS MediaBus Card
5.External Connectors
3.Parallel Printer Connector (26 Pin Block)
Note
4.Serial port COM1 and COM2 connectors (Two 10-pinblocks)
5.Floppy drive connector (34-pinblock )
6.Primary / Secondary IDE connectors (Two 40-pinBlock)
7.Board Power Input (12-pinblock)
8.IDE activity LED
9.Turbo LED lead (CON3)
10.SMI suspend switch lead (CON3)
11.Reset switch lead (CON3)
12.Keyboard lock switch lead (CON3)
13.Speaker connector (CON3)
Power Connection Procedures
6. BIOS Setup
Standard CMOS Setup
Details of Standard CMOS Setup:
For an IDE hard disk drives, you can:
•Use theAuto setting for detection during bootup (see below)
•Enter the specifications yourself manually by using the “User” option
Auto detection of hard disks on bootup (New Feature)
Drive A, Drive B
Floppy 3 Mode Support
Video
Halt On
This field determines which types of errors will cause the system to halt
BIOS Features Setup
Details of BIOS Features Setup:
(BIOS
CPU Internal Cache / External Cache
Enable
Disable
Quick Power On Self Test
Typematic Rate (Char/Sec)
Typematic Delay (Msec)
250ms
Security Option
System
Chipset Features Setup
[DRAM and ECC]
DRAM are 72 bits wide
Memory parity SERR# (NMI):
DRAM ECC/PARITY Select:
DRAM are 64 (not 72) bits wide
(Chipset
Onboard Parallel Port
3BCH / IRQ 7
378H / IRQ
, 278H / IRQ 5, Disabled
Power Management Setup
Details of Power Management Setup:
(Power
Video Off Option
Susp
Stby
Off
PNP and PCI Setup
& (Plug
IRQ xx Used By ISA
No/ECU
Yes
IRQ10 Used By ISA
Load BIOS Defaults
Load Setup Defaults
Supervisor Password and User Password
IDE HDD Auto Detection
Save and Exit Setup
Exit Without Saving
Flash Memory Writer Utility
The Flash Memory Writer Utility Screen:
1. Save Current BIOS to File
2. Update BIOS Main Block from File
Boot Block of New BIOS is different from old one
Please Use 'Advanced Feature' to flash whole bios
3. Advanced Features
DO NOT TURN OFF THE SYSTEM IF THERE IS A PROBLEM
then turn off your system
Desktop Management Interface (DMI)
Introducing the DMI utility
System Requirements
Using the DMI utility
Notes:
Save MIFD
Load MIFD
Load BIOS Defaults
(This page was intentionally left blank)
NCR SCSI BIOS and Drivers
The PCI-SC200SCSI Interface Card
Setting Up the PCI-SC200
Setting the INT Assignment
Terminator Settings
ID (SCSI
PCI
only
must
both
