Asus P/I-P55T2P4S Map of the ASUS Motherboard, III. INSTALLATION

INSTALLATION .III Board) of (Map

III. INSTALLATION

Map of the ASUS Motherboard

PS/2

Key-

Keyboard BIOS

Universal Serial

Mouse

board

Super

Bus (Reserved)

Multi-I/O

COM 1

COM 2

Chipset

3 Slot ISA

2 Slot ISA

1 Slot ISA

Parallel (Printer) Port

Serial (COM) Ports

ConnectorSCSI Pin-50

4Slot PCI

3Slot PCI

2Slot PCI

(En/Dis)I/O-Multi

1Slot PCI

Adaptec 7880

SCSIWidePin-68

1 35

SCSI Chipset

34 68

Socket SIMM

Drives Floppy

MediaBus

2) (Bank 6

2) (Bank 5

1) (Bank 4

1) (Bank 3

0) (Bank 2

0) (Bank 1

0.2

Board

IDE Primary

IDE Secondary

Input Power

Clock Freq

Boot Block Write

RTC Clear

CPU ZIF Socket 7

Fan Pwr 1

Infrared

BF1 BF0

TAG

Cacheable

Intel 430HX

Fan Pwr 2

PCIset

64/512MB

HD LED

UpgradeSRAM

Onboard SRAMTag

Case

Freq. Ratio

Connector

VID1 VID0

VID3 VID2

Vcore Voltage

512KB Pipelined Burst L2 Cache

4	ASUS P/I-P55T2P4S User’s Manual

Contents

Page USER'S NOTICE © Copyright 1996 ASUSTeK COMPUTER INC. All rights reserved Product Name: ASUS P/I-P55T2P4S Manual Revision: ASUSTeK COMPUTER INC Marketing Info: Technical Support: ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE V. DESKTOP MANAGEMENT VI. ADAPTEC EZ-SCSIUTILITY VII. ADAPTEC 7800 DRIVERS (88 Pages) FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this manual is organized Item Checklist Features of the ASUS Motherboard Parts of the ASUS Motherboard Map of the ASUS Motherboard Jumpers Expansion Slots Connectors INSTALLATION (Map of Board) Installation Steps 1. Jumpers Jumper Settings TAG SRAM Upgrade III.INSTALLATION 2.Flash ROM Boot Block Programming (BBLKW) Programming BBLKW Disabled [1-2] 4.Real Time Clock (RTC) RAM (RTCLR) Selections RTCLROperation [open] (Default) Clear Data [short] (momentarily) 5.CPU External (BUS) Frequency Selection (FS1, FS2) External BUS Clock Internal 6.CPU to BUS Frequency Ratio (BF0, BF1) Cyrix CPU Identification 2.System Memory (DRAM & SRAM) DRAM Memory Installation Procedures: (This page was intentionally left blank) 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards 5.External Connectors 3.Parallel Printer Connector (26 Pin Block) NOTE: Serial printers must be connected to the serial port 4.Serial Port COM1 and COM2 Connectors (Two 10-pinblocks) wrong orientation when using ribbon cables with pin 10 plugged) 5.Floppy Drive Connector (34-pinblock ) 6.Power Connector (12-pinblock) 7.Primary / Secondary IDE Connectors (Two 40-pinBlock) 8.IDE Activity LED (HDLED) 9.Turbo LED Lead (PANEL) 10.SMI Suspend Switch Lead (PANEL) 11.Reset Switch Lead (PANEL) 12.Keyboard Lock Switch Lead & System Power LED (PANEL) 13.Speaker Connector (PANEL) 14.CPU Cooling Fan Connector (FAN) These are not jumpers, do not place jumper caps over these pins 15.IrDA-CompliantInfrared Module Connector (IR) 16.Ultra-FastSCSI & Ultra-WideSCSI Connectors Onboard SCSI Connectors Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Updating your Motherboard's BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: For IDE hard disk drive setup, you can: •Use the Auto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option CYLS HEAD Drive A, Drive B Floppy 3 Mode Support Video Halt On This field determines which types of errors will cause the system to halt BIOS Features Setup Details of BIOS Features Setup: External Cache Quick Power On Self Test HDD Sequence SCSI/IDE First (New Feature!) IDE SCSI Typematic Rate Setting Typematic Rate (Chars/Sec) 8, 10, 12, 15, 20, 24 Typematic Delay (Msec) 250ms Chipset Features Setup (Chipset [DRAM and ECC] Memory parity SERR# (NMI) Parity ECC Onboard Parallel Port 3BCH / IRQ 7 378H / IRQ , 278H / IRQ 5, Disabled Parallel Port Mode Power Management Setup Details of Power Management Setup: Suspend Switch Doze Speed, Stdby Speed PM Timers HDD Power Down Mins PNP and PCI Setup ISA MEM Block BASE Onboard AHA BIOS Auto USB Function Play / PCI) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save and Exit Setup Exit Without Saving Page Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes: Save MIFD Load MIFD Load BIOS Defaults Page Quick Start Instructions Windows95 or WindowsNT Windows/Windows for Workgroups DOS Troubleshooting Tips SCSI Device Troubleshooting Windows95/WindowsNT Troubleshooting Place the Windows95 3Click on the Have Disk button, then click the Browse button What do I need to do if I want to use another host adapter Open the Control Panel Double-click •You are running in MSDOS mode •You have an older model SCSI-1CDROM drive that Windows95 does not support You are using a Restart the computer in MS-DOS Information for DOS/Windows 3.1x Users DOS and Windows3.1x Device Drivers DOS and Windows3.1x ASPI Managers DOS Formatting Utilities Low-levelFormatter (scsifmt) Formatter and Partitioner (afdisk) 7.To quit afdisk, press Esc and select Yes to confirm that you want to quit Removable Media Manager (rmvtool)