Page
USER'S NOTICE
© Copyright 1996 ASUSTeK COMPUTER INC. All rights reserved
Product Name:
ASUS P/I-P55TVP4
Manual Revision:
ASUSTeK COMPUTER INC
Marketing Info:
Technical Support:
ASUS COMPUTER INTERNATIONAL
ASUS COMPUTER GmbH
CONTENTS
VIII. DOS 3.1 & Windows 3.1x Audio Software
IX. Windows 95 Audio Software
FCC & DOC COMPLIANCE
Federal Communications Commission Statement
•This device may not cause harmful interference, and
•Re-orientor relocate the receiving antenna
•Increase the separation between the equipment and receiver
How this manual is organized
Item Checklist
Features of This Motherboard
Parts of the Motherboard
Map of the Motherboard
Jumpers
Expansion Slots
Connectors
Installation Steps
1. Jumpers
Jumper Settings
III.INSTALLATION
3.Total Level 2 Cache Size Setting (JP4)
Selections JP4
256KB
512KB
Cyrix CPU Identification (for compatible Cyrix CPU's)
6.CPU External (BUS) Frequency Selection (JP1, JP2, JP3)
External
BUS Clock
Internal
7.CPU to BUS Frequency Ratio (JP5, JP6)
2.System Memory (DRAM/SDRAM & SRAM)
Install memory in any or all of the banks in any combination as follows:
DRAM Memory Installation Procedures:
SDRAM Memory Installation Procedures:
Static RAM (SRAM) for Level 2 (External) Cache
Compatible Cache Modules for this Motherboard
3.Central Processing Unit (CPU)
4.Expansion Cards
Expansion Card Installation Procedure:
Assigning IRQs for Expansion Cards
Assigning DMA Channels for ISA Cards
(This page was intentionally left blank)
5.External Connectors
3.Parallel Printer Connector (26 Pin Block)
NOTE: Serial printers must be connected to the serial port
4.Serial port COM1 and COM2 connectors (Two 10-pinblocks)
5.Floppy drive connector (34-pinblock )
6.Power connector (12-pinblock)
7.Primary / Secondary IDE connectors (Two 40-pinBlock)
8.IDE activity LED (IDE LED)
9.Turbo LED Lead (CON1)
10.SMI Suspend Switch Lead (CON1)
11.Reset Switch Lead (CON1)
12.Keyboard Lock Switch Lead & System Power LED (CON1)
13.Speaker Connector (CON1)
14.IrDA-compliantinfrared module connector (IR)
Power Connection Procedures
Support Software
Flash Memory Writer Utility
Main Menu
Advanced Features Menu
Updating your Motherboard's BIOS
6. BIOS Setup
Load Defaults
Standard CMOS Setup
Details of Standard CMOS Setup:
For IDE hard disk drive setup, you can:
•Use the Auto setting for detection during bootup
•Enter the specifications yourself manually by using the “User” option
CYLS
HEAD
Drive A / Drive B (None)
Floppy 3 Mode Support (Disabled)
Drive A, Drive B, Both, and Disabled
Video (EGA/VGA)
EGA/VGA, Mono (for Hercules or MDA), CGA 40, and CGA
BIOS Features Setup
Details of BIOS Features Setup
External Cache (Enabled)
Quick Power On Self Test (Enabled)
Enabled
HDD Sequence SCSI/IDE First (New Feature!)
IDE
Typematic Rate Setting (Disabled)
Disabled
Typematic Rate (Chars/Sec)
8, 10, 12, 15, 20, 24
Typematic Delay (Msec) (250ms)
Chipset Features Setup
Details of Chipset Features Setup
(Chipset
Memory Hole at Address (None)
14MB-16MB
15MB-16MB
Onboard FDC Controller (Enabled)
ECP DMA Select (3)
ECP
ECP+EPP
Parallel Port Mode
UART2 Use Infrared (Disabled)
Power Management Setup
Details of Power Management Setup
Video Off Method (V/H SYNC + Blank)
Suspend Switch (Enabled)
Doze Speed, Stdby Speed
PM Timers
HDD Power Down
PNP and PCI Setup
Details of PNP and PCI Setup
DMA x Used By ISA (No/ICU)
ISA MEM Block BASE (No/ICU)
NCR SCSI BIOS (Auto)
USB Function (Disabled)
Play / PCI)
Load BIOS Defaults
Load Setup Defaults
Supervisor Password and User Password
IDE HDD Auto Detection
Save and Exit Setup
Exit Without Saving
Page
Desktop Management Interface (DMI)
Introducing the ASUS DMI Configuration Utility
System Requirements
Using the ASUS DMI Configuration Utility
Notes:
Save MIFD
Load MIFD
Load BIOS Defaults
Page
NCR SCSI BIOS and Drivers
The ASUS PCI-SC200SCSI Interface Card
Setting Up the ASUS PCI-SC200
Setting the INT Assignment
Terminator Settings
SCSI ID Numbers
ASUS I-A16CAudio Features
Unpacking and Handling Precautions
Layout and Connectors
Connectors
CD-AudioConnector Pin Definitions