Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus P/I-P55TVP4 Chipset Features Setup, 14.IrDA-compliantinfrared module connector (IR)

1 64

Download 64 pages, 794.05 Kb

INSTALLATION .III (Connectors)

III.INSTALLATION

14.IrDA-compliant infrared module connector (IR)

This connector supports the optional wireless transmitting and receiving infra- red module. This module mounts to a small opening on system cases that sup- port this feature. You must also configure the setting through "UART2 Use Infrared" in Chipset Features Setup to select whether UART2 is directed for use with COM2 or IrDA. Use the five pins as shown on the Back View and connect a ribbon cable from the module to the motherboard according to the pin definitions.

Front View

Back View

+5V

IRRX

GND

IRTX

IRTX +5V

GND NC

IRRX

Infrared Module Connector

24	ASUS P/I-P55TVP4 User's Manual

Contents

Page USER'S NOTICE © Copyright 1996 ASUSTeK COMPUTER INC. All rights reserved Product Name: ASUS P/I-P55TVP4 Manual Revision: ASUSTeK COMPUTER INC Marketing Info: Technical Support: ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS VIII. DOS 3.1 & Windows 3.1x Audio Software IX. Windows 95 Audio Software FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this manual is organized Item Checklist Features of This Motherboard Parts of the Motherboard Map of the Motherboard Jumpers Expansion Slots Connectors Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.Total Level 2 Cache Size Setting (JP4) Selections JP4 256KB 512KB Cyrix CPU Identification (for compatible Cyrix CPU's) 6.CPU External (BUS) Frequency Selection (JP1, JP2, JP3) External BUS Clock Internal 7.CPU to BUS Frequency Ratio (JP5, JP6) 2.System Memory (DRAM/SDRAM & SRAM) Install memory in any or all of the banks in any combination as follows: DRAM Memory Installation Procedures: SDRAM Memory Installation Procedures: Static RAM (SRAM) for Level 2 (External) Cache Compatible Cache Modules for this Motherboard 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards (This page was intentionally left blank) 5.External Connectors 3.Parallel Printer Connector (26 Pin Block) NOTE: Serial printers must be connected to the serial port 4.Serial port COM1 and COM2 connectors (Two 10-pinblocks) 5.Floppy drive connector (34-pinblock ) 6.Power connector (12-pinblock) 7.Primary / Secondary IDE connectors (Two 40-pinBlock) 8.IDE activity LED (IDE LED) 9.Turbo LED Lead (CON1) 10.SMI Suspend Switch Lead (CON1) 11.Reset Switch Lead (CON1) 12.Keyboard Lock Switch Lead & System Power LED (CON1) 13.Speaker Connector (CON1) 14.IrDA-compliantinfrared module connector (IR) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Updating your Motherboard's BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: For IDE hard disk drive setup, you can: •Use the Auto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option CYLS HEAD Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) EGA/VGA, Mono (for Hercules or MDA), CGA 40, and CGA BIOS Features Setup Details of BIOS Features Setup External Cache (Enabled) Quick Power On Self Test (Enabled) Enabled HDD Sequence SCSI/IDE First (New Feature!) IDE Typematic Rate Setting (Disabled) Disabled Typematic Rate (Chars/Sec) 8, 10, 12, 15, 20, 24 Typematic Delay (Msec) (250ms) Chipset Features Setup Details of Chipset Features Setup (Chipset Memory Hole at Address (None) 14MB-16MB 15MB-16MB Onboard FDC Controller (Enabled) ECP DMA Select (3) ECP ECP+EPP Parallel Port Mode UART2 Use Infrared (Disabled) Power Management Setup Details of Power Management Setup Video Off Method (V/H SYNC + Blank) Suspend Switch (Enabled) Doze Speed, Stdby Speed PM Timers HDD Power Down PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) NCR SCSI BIOS (Auto) USB Function (Disabled) Play / PCI) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save and Exit Setup Exit Without Saving Page Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes: Save MIFD Load MIFD Load BIOS Defaults Page NCR SCSI BIOS and Drivers The ASUS PCI-SC200SCSI Interface Card Setting Up the ASUS PCI-SC200 Setting the INT Assignment Terminator Settings SCSI ID Numbers ASUS I-A16CAudio Features Unpacking and Handling Precautions Layout and Connectors Connectors CD-AudioConnector Pin Definitions