Asus P/I-P55TVP4 Map of the Motherboard

III. INSTALLATION

Map of the Motherboard


PS/2 Mouse									Keyboard
PS/2 Mouse									Keyboard

INSTALLATION .III Board) of (Map

Boot

COM 1

COM 2

ISA

I/OMulti

Parallel Printer

Program

Multi I/O

Super

3 Slot

2 Slot

1 Slot

PCI

JP10

JP9

PCI

Board Power Input

0.2MediaBus/ 4 Slot

3 Slot

2 Slot

1 Slot

IDE Primary

IDESecondary

DrivesFloppy

2)(BankSlotDIMM

0)(Bank1SlotSIMM

0)(Bank2SlotSIMM

1)(Bank3SlotSIMM

1)(Bank4SlotSIMM

IDE LED	Clear CMOS
1) (CON Conn Case	JP7
1) (CON Conn Case	.Con Infrared

Vio/Vcore

JP22

JP21

JP20

JP19

JP18

JP17

JP16

BUS Ratio

JP6

JP5

ZIF Socket 7

L2 CACHE

JP4

Slot Expansion Cache 2 Level Burst Pipelined

BUS FREQ

JP3

JP2

JP1

256/512KB OnBoard L2 Cache

4	ASUS P/I-P55TVP4 User's Manual

Contents

Page USER'S NOTICE © Copyright 1996 ASUSTeK COMPUTER INC. All rights reserved Product Name: ASUS P/I-P55TVP4 Manual Revision: ASUSTeK COMPUTER INC Marketing Info: Technical Support: ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS VIII. DOS 3.1 & Windows 3.1x Audio Software IX. Windows 95 Audio Software FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this manual is organized Item Checklist Features of This Motherboard Parts of the Motherboard Map of the Motherboard Jumpers Expansion Slots Connectors Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.Total Level 2 Cache Size Setting (JP4) Selections JP4 256KB 512KB Cyrix CPU Identification (for compatible Cyrix CPU's) 6.CPU External (BUS) Frequency Selection (JP1, JP2, JP3) External BUS Clock Internal 7.CPU to BUS Frequency Ratio (JP5, JP6) 2.System Memory (DRAM/SDRAM & SRAM) Install memory in any or all of the banks in any combination as follows: DRAM Memory Installation Procedures: SDRAM Memory Installation Procedures: Static RAM (SRAM) for Level 2 (External) Cache Compatible Cache Modules for this Motherboard 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards (This page was intentionally left blank) 5.External Connectors 3.Parallel Printer Connector (26 Pin Block) NOTE: Serial printers must be connected to the serial port 4.Serial port COM1 and COM2 connectors (Two 10-pinblocks) 5.Floppy drive connector (34-pinblock ) 6.Power connector (12-pinblock) 7.Primary / Secondary IDE connectors (Two 40-pinBlock) 8.IDE activity LED (IDE LED) 9.Turbo LED Lead (CON1) 10.SMI Suspend Switch Lead (CON1) 11.Reset Switch Lead (CON1) 12.Keyboard Lock Switch Lead & System Power LED (CON1) 13.Speaker Connector (CON1) 14.IrDA-compliantinfrared module connector (IR) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Updating your Motherboard's BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: For IDE hard disk drive setup, you can: •Use the Auto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option CYLS HEAD Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) EGA/VGA, Mono (for Hercules or MDA), CGA 40, and CGA BIOS Features Setup Details of BIOS Features Setup External Cache (Enabled) Quick Power On Self Test (Enabled) Enabled HDD Sequence SCSI/IDE First (New Feature!) IDE Typematic Rate Setting (Disabled) Disabled Typematic Rate (Chars/Sec) 8, 10, 12, 15, 20, 24 Typematic Delay (Msec) (250ms) Chipset Features Setup Details of Chipset Features Setup (Chipset Memory Hole at Address (None) 14MB-16MB 15MB-16MB Onboard FDC Controller (Enabled) ECP DMA Select (3) ECP ECP+EPP Parallel Port Mode UART2 Use Infrared (Disabled) Power Management Setup Details of Power Management Setup Video Off Method (V/H SYNC + Blank) Suspend Switch (Enabled) Doze Speed, Stdby Speed PM Timers HDD Power Down PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) NCR SCSI BIOS (Auto) USB Function (Disabled) Play / PCI) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save and Exit Setup Exit Without Saving Page Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes: Save MIFD Load MIFD Load BIOS Defaults Page NCR SCSI BIOS and Drivers The ASUS PCI-SC200SCSI Interface Card Setting Up the ASUS PCI-SC200 Setting the INT Assignment Terminator Settings SCSI ID Numbers ASUS I-A16CAudio Features Unpacking and Handling Precautions Layout and Connectors Connectors CD-AudioConnector Pin Definitions