Asus P2B-D2 Layout

III. INSTALLATION

The ASUS P2B-D2 Motherboard Layout

Top:

Mouse

PS/2 Bottom:

Keyboard

Top:

USB USBBottom: 1

USB 2

COM 1

Connector

Parallel Port

Single Edge Contact Slot 1 (for Pentium II processor)

Intel

440BX

AGPset

J1601

PWR_FAN

				ATXPWR
				CHA _FAN
				CHA _FAN			P10
							P10
				35 1		SCSI Connector	PWR-CON2
pin module)	pin module)							P9
pin module)	pin module)
3 (64/72 bit, 168	4 (64/72 bit, 168					68-pin Ultra-Wide		P8

				68 34
							PWRCON

.III

Board

	VGA		CPU Heat Sensor
			Connector
			Connector

RJ-45

Single Edge Contact Slot 1 (for Pentium II processor)

Floppy

512KB DRAM

512KB DRAM

upgrade socket

upgrade socket

COM 2

S3

Trio64V2/DX

512KB DRAM

512KB DRAM

VGA

for onboard VGA

for onboard VGA

Chipset

CPU Heat Sensor Connector

J1602

PCI Slot 1

CPU_FAN

FS0

FS1

FS2

Bus Freq.

CLRTC

DIMMSocket

DIMMSocket

50-pin Narrow SCSI Connector

Connector

Adaptec

1

35

7890

SCSI

SCSI

Chipset

CR2032 3Volts

LVD

Lithium Cell

Ultra2

SCSI_EN

BIOS Power

-pin

68 34

68

INSTALLATION

Layout

	Multi-I/O
	Chip
					PCI Slot 2			Intel


								i960
	IOAPIC				PCI Slot 3			Processor
										960SEL




					Secondary PCI Slot 1
					Secondary PCI Slot 1

					LAN_EN
		2Mbit Flash EEPROM	(Programable BIOS)		LAN_EN
					Secondary PCI Slot 2		Intel
							82558
							LAN
					Secondary PCI Slot 3		Chipset

ISA Slot 1

IDE2

EXT BATT

Intel

IDE1

Chipset

i960 SIMM Socket 2 (Bank 1)

i960 SIMM Socket 1 (Bank 0)

SBLINK

DRAMRAS

CHASSIS

i960

i960

NVRAM

Firm-

Firm-

ware

ware

Hardware

ASUS

i960

i960

Monitor

Firm-

Firm-

ASIC

ware

ware

BF3BF2BF1BF0 Chassis Intrusion Sensor

Alert

Freq.

Pack

JP1601

Panel

Mult.

HDLED

Infrared

10	ASUS P2B-D2 User’s Manual

Contents

Page Product Name: ASUS P2B-D2 Manual Revision: 1.02 E275 Release Date: Marketing Technical Support Page Page Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help This manual is divided into the following sections: Introduction Manual information and checklist Features Information and specifications FEATURES Specifications P2B Motherboard Parts II. FEATURES Layout Jumpers Expansion Slots/Sockets Hardware Monitor Connectors INSTALLATION Jumpers Before using your computer, you must complete the following steps: 1.Set Jumpers on the Motherboard 2.Install System Memory Modules 3.Install the Central Processing Unit (CPU) Jumper Settings 4.CPU Bus Frequency (FS0, FS1, FS2) 5.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External CPU Bus Frequency 6.Chassis Intrusion Sensor Setting (JP1601) JP1601 7.LAN Setting (LAN_EN) LAN EN 8.SCSI Setting (SCSI_EN) Memory System Main Memory (DIMM) 3.3Volt SDRAM Configuration IMPORTANT (see General DIMM Notes below) DIMM Memory Installation Procedures SIMM Installation Pentium II Processor Other Important Items Installing the Pentium II Processor Mount the Heatsink: IMPORTANT: The heatsinks must not be more than 2.8 cm (1.1 inch) thick IMPORTANT: Secure the SEC Cartridge: Connect the Heat Sensor Cable to J1601/J1602: AAVID Heatsink Elan Vital Heatsink Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor Connectors 1.PS/2 Keyboard Connector (6 pin Female) 2.PS/2 Mouse Connector (6 pin Female) 3.Parallel Printer Connector (25 pin Female) NOTE 4.Serial Port COM1 Connector (9 pin Male) 7.RJ-45Connector (8 pin Female) 8.Hard Disk Activity LED (2 pin IDELED) 9.Primary / Secondary IDE Connectors (Two 40-1pin IDE) 10.Chassis Intrusion Sensor Lead (CHASSIS) 11.IrDA-Compliantinfrared module connector (5 pin IR) 12.Chassis, CPU, & Power Supply Fan Connectors (3 pin FAN) These are not jumpers, do not place jumper caps over these pins 14.ATX Power Supply Connector (20 pin ATXPWR) 15.LED Lead (MSG.LED) 16.System Management Interrupt Lead (SMI) 17.ATX Power Switch / Soft Power Switch (PWR.SW) 18.Reset Switch Lead (RESET) 19.System Power LED (PWR.LED) 22.50 pin Narrow/68 pin Wide/68 pin Ultra2 SCSI Connectors 23.SB-Link™Connector (6-1pin SBLINK) 24.Floppy Disk Drive Connector (34-1pinFLOPPY) 25.Serial Port COM 2 (COM2, 10-1pins) 26.VGA Memory Upgrade Sockets Page Power Connection Procedures 1.After all connections are made, close the system case cover 2.Be sure that all switches are off (in some systems, marked with ) 5.You may then turn on your devices in the following order: a.Your monitor Main Menu 2. Update BIOS Including Boot Block and ESCD When prompted to confirm the BIOS update, press Y to start the update Flashed Successfully will be will be displayed Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 2.Copy AFLASH.EXE to the just created boot disk Run AFLASH.EXE from this new disk and select option 1. Save Current BIOS to File BIOS Setup Load Defaults Details of Standard CMOS Setup: Time (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup Auto detection of hard disks on bootup Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) Details of BIOS Features Setup BIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache BIOS Update (Enabled) PS/2 Mouse Function Control (Auto) OS/2 Onboard Memory > 64M (Disabled) MPS 1.4 Support (Disabled) PCI/VGA Palette Snoop (Disabled) Video ROM BIOS Shadow (Enabled) Details of Chipset Features Setup Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Wake On LAN (Enabled) Automatic Power Up (Disabled) Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) Onboard AHA BIOS (Auto) ONB AHA BIOS First (No) ONB SCSI SE Term. (Enabled) Load BIOS Defaults Load Setup Defaults Load Supervisor Password and User Password Clear Time Clock (Jumpers) Passwords IDE HDD Auto Detection Save & Exit Setup Save & Exit Exit Without Saving Page V. SOFTWARE (This page was intentionally left blank) Installing Video drivers in Windows 95 (New Hardware Found) New Hardware Found Driver from disk provided by hard- ware manufacturer Drives: 4.Select VGA\WIN95 Using Control Panel 1.Start Windows 95, switch display to VGA mode, then restart Right-click Properties Settings Changing display settings Display Control Panel Adjustment: Change Refresh Rate: Adjust Performance Hotkey: Settings: 1.Boot Windows NT in standard VGA mode (recommended) Run Windows NT Display program located in the Set- tings Start 3.Select the Settings page Page Features •Wake-On-LANRemote Control Function Supported •PCI Bus Master Complies to PCI Rev •Consists of MAC & PHY (10/100Mbps) interfaces •Fully supports 10BASE-T& 100BASE-TXoperations Layout/Installation NETWORK .B LED Connectors Activity Indicator: Speed Indicator: Automatic configuration Run Setup to install network drivers 5.When Setup finishes the tests, you’ll see the Install Network Drivers screen DOS/Windows Troubleshooting •Verify that the frame type in your NET.CFG file matches your network •If setting up a server, check your LOAD and BIND statements •Check the README files Responder testing on the network (optional) 1.Double-clickthe Network icon in the Control Panel 2.Click the Adapters tab in the window that appears 3.Click Add. A list of network interface or adapter appears 4.Select “Intel EtherExpress PRO Adapter” and click OK Install network drivers - Windows NT Version 3.5x only 95 Windows Automatic Configuration Install Network Drivers from Diskette 3.Insert the ASUS Configuration and Drivers disk 4.Specify A:\ (or B:\) as the path, then click OK Auto (requires a full duplex network interface or adapter or switching hub with auto-negotiation the network interface or adapter runs at half duplex Half duplex Manually Configuring for Full Duplex Mode Duplex NetWare server FORCEDUPLEX=2 SPEED=100 (or 10 if 10BASE-T) For more information, see the README file for NetWare servers If the interface can’t connect to the network Testing the network interface or adapter Common problems and solutions •Make sure your PCI BIOS is current The interface stopped working without apparent cause •Try reconnecting the cable to the RJ45 port first •Try another motherboard of the same model •Run the diagnostics Shared hubs Switching hubs Question and Answer Q: What is Wake-On-LAN The Q: What can Wake-On-LANdo for you Q: What components does Wake-On-LANrequire to be enable 100Base-TX IEEE’s specification for running 100Mbps Ethernet using twisted-paircables 10Base-T IEEE’s specification for running 10Mbps Ethernet using twisted-paircables 10Base2 Adaptec AIC-7890SCSI BIOS Build (c) 1998 Adaptec, Inc. All Rights Reserved <<< Press <Ctrl><A> for SCSISelect(TM) Utility SCSI Disk Utilities Format Disk Start Intro/Quick Note: Windows95 or WindowsNT Windows/Windows for Workgroups 2Insert the Adaptec EZSCSI Setup Disk into your floppy disk drive SCSI Device Troubleshooting Be sure Windows95/WindowsNT Troubleshooting Place the Windows95 Select No on the second screen, and select SCSI controllers on the next screen 3Click on the Have Disk button, then click the Browse button What do I need to do if I want to use another host adapter Open the Control Panel If I am running under Windows95, do I need lines for the Adaptec real mode CONFIG.SYS AUTOEXEC.BAT •You are running in MSDOS mode You are using a scanner or another SCSI device with CONFIG.SYS- or .Info DOS/Win DOS and Windows3.1x Device Drivers DOS and Windows3.1x ASPI Managers Low-levelFormatter (scsifmt) Formatter and Partitioner (afdisk) 7.To quit afdisk, press Esc and select Yes to confirm that you want to quit Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults LAN Card •Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) •PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications •Complies to IEEE 802.3 10BASE-Tand IEEE 802.3u 100BASE-TXinterfaces •Fully supports 10BASE-T& 100BASE-TXoperations through a single RJ45 port •Supports 32-bitBus Master Technology / PCI Rev