Asus P2L97 Layout of the ASUS P2L97 Motherboard

INSTALLATION .III Layout) (Board

III. INSTALLATION

Layout of the ASUS P2L97 Motherboard

		Top:	PWR_FAN	CPU_FAN
PS/2		Mouse	PWR_FAN	CPU_FAN
PS/2		Bottom:
		Keyboard		JP1
		KB_UP		JP1
PortParallel	2COMCOM 1	KB_UP	ContactEdgeSingleCPU Slot	Pentium II Thermal	168bit,(64/722Socketpin module)	168bit,(64/721Socketpin module)
PortParallel	2COMCOM 1	ATX PowerConenctor	ContactEdgeSingleCPU Slot	168bit,(64/723Socketpin module)	168bit,(64/722Socketpin module)	168bit,(64/721Socketpin module)
		Top:		Sensor Connector
USB		USB 1		Sensor Connector
USB		Bottom:
		USB 2
				Intel			CR2032 3V
				440LX			CR2032 3V
				440LX			Lithium Cell
				AGPset			(BIOS Power)
								CLRTC
				DIMM	DIMM	DIMM
						Floppy Drives	Secondary IDE	Primary IDE
				Accelerated Graphics Port
		WOL_CON
		Multi-I/O		PCI Slot 1
		Multi-I/O				BUS FREQ
						BUS FREQ
						FS0
						FS1
				PCI Slot 2		FS2
		EEPROMFlash (ProgramableBIOS)		PCI Slot 2
		EEPROMFlash (ProgramableBIOS)		PCI Slot 3	Intel PIIX4
				PCI Slot 3

					PCIset
								CHA_FAN
				PCI Slot 4
		Hardware		R
		Monitor				BF3 BF2 BF1 BF0
		LM78		PCI Slot 5		BF3 BF2 BF1 BF0
		LM78
					BUS FREQ
				ISA Slot 1
						IR Connector
RT2MB						IDE LED
RT2MB
Thermal				ISA Slot 2		Panel Connectors
Sensor						Panel Connectors

10	ASUS P2L97 User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS P2L97 Manual Revision: 2.05 E266 ASUSTeK COMPUTER INC Marketing Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE Details of Standard CMOS Setup: Details of BIOS Features Setup Details of Chipset Features Setup Details of Power Management Setup Details of PNP and PCI Setup FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS P2L97 Motherboard The ASUS P2L97 Motherboard Layout of the ASUS P2L97 Motherboard Jumpers Expansion Slots/Sockets Hardware Monitor Connectors Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.CPU Bus Frequency (FS0, FS1, FS2) 4.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External Page Page 2.System Memory (DIMM) DIMM Memory Installation Procedures: 3.Central Processing Unit (CPU) Universal Retention Mechanism Heatsinks Installing the Processor 3.Insert the SECC/SECC2/SEPP SECC with Pentium II only: 4.Secure the SECC/SECC2/SEPP ASUS Smart Thermal Solutions Recommended Heatsinks for Pentium II Processors 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor 5.External Connectors 3.Parallel Printer Connector (25-pinFemale) NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinMale) 5.Floppy Disk Drive Connector (34-1pinFLOPPY) (Connectors) 7.Primary / Secondary IDE connectors (Two 40-1pinIDE) 8.IDE activity LED (2-pinIDE_LED) 9.Chassis , CPU , & Power Supply Fan Connectors (3-pinFANPWR) do not place jumper caps over these pins 10.IrDA-CompliantInfrared Module Connector (5-pinIR) 11.ATX Power Supply Connector (20-pinATXPWR) 12.Wake-On-LAN (3-pinWOL) 13.Message LED Lead (MSG LED) 14.System Management Interrupt Lead (SMI) 15.ATX Power Switch / Soft Power Switch (PWR SW) 16.Reset Switch Lead (RESET) 17.System Power LED (PWR LED) Power Connection Procedures Flash Memory Writer Utility Main Menu 2. Update BIOS Including Boot Block and ESCD When prompted to confirm the BIOS update, press Y to start the update Flashed Successfully will be will be displayed Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup Auto detection of hard disks on bootup Auto Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled BIOS Features Setup Details of BIOS Features Setup (BIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache BIOS Update (Enabled) PCI/VGA Palette Snoop (Disabled) Video ROM BIOS Shadow (Enabled) C8000 - CBFFF Shadow to DC000 - DFFFF Shadow (Disabled) Boot Up NumLock Status (On) This field allows users to activate the Number Lock function upon system boot Chipset Features Setup Details of Chipset Features Setup Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Enabled Wake On LAN (Enabled) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) USB IRQ (Enabled) VGA BIOS Sequence (PCI/AGP) PCI/AGP Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving