Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus P2Z-VM ASUS P2Z-VMUser’s Manual, 25.ATI Multimedia Channel Connector (40-3pin AMC), 26.ATX Power Supply Connector (20-pinblock ATXPWR)

1 96

Download 96 pages, 2.34 Mb

III.HARDWARE SETUP

25.ATI Multimedia Channel Connector (40-3 pin AMC)

This connector is used for video accessories such as video capture cards or tele- vision tuners.

4039

P2Z-VM

P2Z-VM ATI Multimedia Channel Connector	2	1
P2Z-VM ATI Multimedia Channel Connector

26.ATX Power Supply Connector (20-pin block ATXPWR)

This connector connects to an ATX power supply. The plug from the power sup- ply will only insert in one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned.

IMPORTANT: Make sure that your ATX power supply can supply at least 10mA on the 5-volt standby lead (+5VSB). You may experience difficulty in powering on your system if your power supply cannot support the load. For Wake-On- LAN support, your ATX power supply must supply at least 720mA +5VSB.

	+3.3	Volts	+3.3 Volts
	-12.0 Volts		+3.3 Volts
	Ground		Ground
	Power Supply On		+5.0 Volts
	Ground		Ground
	Ground		+5.0 Volts
	Ground		Ground
	-5.0 Volts		Power Good
P2Z-VM	+5.0 Volts		+5V Standby
	+5.0 Volts		+12.0 Volts

P2Z-VM ATX Power Connector

Connectors

III. H/W SETUP

ASUS P2Z-VM User’s Manual

35

Contents

Page USER'S NOTICE Product Name: ASUS P2Z-VM Manual Revision: 1.02 E352 ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) CONTENTS Page FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS P2Z-VMMotherboard II.FEATURES Wake-On-LAN: IrDA: Special Features: Enhanced ACPI and Intelligent Features: Auto Fan Off: even in sleep mode and system noise The ASUS P2Z-VMMotherboard Layout of the ASUS P2Z-VMMotherboard Jumpers Expansion Slots Connectors Layout Contents Hardware Setup Steps 1. Motherboard Settings Jumpers III.HARDWARE SETUP 2.VGA Setting (VGAEN) VGAEN (default) 3.Keyboard Power (Wake) Up (KB_WAK) 4.Audio Setting (AUDIO_EN) The onboard 32-bitPCI audio may be enabled or disabled using this jumper 5.CPU Bus Frequency Selection (FS0, FS1, FS2, FS3, FS4) External BUS Clock 6.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Set the jumpers by the Internal speed of your processor as follows: NOTES: Page 2.System Memory (DIMM) DIMM Memory Installation Procedures: 3.Central Processing Unit (CPU) Universal Retention Mechanism Heatsinks Installing the Processor 3.Insert the SECC/SECC2/SEPP SECC with Pentium II only: 4.Secure the SECC/SECC2/SEPP Recommended Heatsinks for Slot 1 Processors 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards Accelerated Graphics Port 5.External Connectors 3.Parallel Port Connector (25-pinPRINTER) NOTE 4.Serial Port COM1 Connector (9-pinCOM1) 5.Monitor (VGA) Output Connector (15-pinVGA) Audio Port Connectors (Three 1/8” Female) Line Out Line In Mic 9.Primary / Secondary IDE Connectors (Two 40-1pinIDE) 10.Floppy Disk Drive Connector (34-1pinFLOPPY) 11.IrDA-CompliantInfrared Module Connector (5-pinIR) 12.Wake-On-LANConnector (3-pinWOL_CON) WAKE On LAN Power Up Con- trol do not place jumper caps over these pins 14.SB-Link™Connector (6-1pin SB-LINK) 15.Internal Audio Connectors (4-pinCD_IN and MODEM_IN) 16.Serial Port COM 2 Header (10-1pin COM2) 17.Message LED Lead (2-pinMLED) 18.Keyboard Lock Switch Lead (2-pinKEYLOCK) 19.System Management Interrupt Lead (2-pinSMI) 21.ATX Power Switch/Soft Power Switch (2-pinPWR) 22.IDE Activity LED (2-pinIDELED) 25.ATI Multimedia Channel Connector (40-3pin AMC) 26.ATX Power Supply Connector (20-pinblock ATXPWR) Page Power Connection Procedures Flash Memory Writer Utility Main Menu 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup Auto detection of hard disks on bootup Drive A Floppy 3 Mode Support Drive A, Drive B, Both, and Disabled Video BIOS Features Setup Details of BIOS Features Setup Features BIOS Processor Serial Number (Enabled) CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache PS/2 Mouse Function Control (Auto) OS/2 Onboard Memory > 64M (Disabled) PCI/VGA Palette Snoop (Disabled) Video ROM BIOS Shadow (Enabled) C8000-CBFFFto DC000-DFFFF(Disabled) Chipset Features Setup Details of Chipset Features Setup Timing for 16-bitand 8-bitISA cards, respectively. Leave on default setting Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Features Chipset Parallel Port Mode (ECP+EPP) ECP DMA Select (3) ECP ECP+EPP Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Power Up By Keyboard (Disabled) Wake On LAN (Disabled) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SYMBIOS SCSI BIOS (Auto) USB IRQ (Enabled) ONB VGA BIOS First (No) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Hard Disk Detect Save & Exit Setup Exit Without Saving Page SOFTWARE CONTENTS V. SOFTWARE SETUP VI. SOFTWARE REFERENCE Windows 98 First Time Installation Installing Plug-and-PlayHardware Onboard Audio Onboard Video P2Z-VMSupport CD Autorun Screen Installing the Video Driver and Utility Making Monitor Adjustments Adjustment Page Color Page Displays Page Installing Audio Utilites Installing the Software Wavetable Installing PCCillin Page ATI Player Task Control Panel Audio CD Player To Play Audio CDs MPEG Player TV Tuner Teletext Capture Capturing Still Images from Television Capturing Still Images from MPEG Clips Capturing a Sequence of Frames Capturing a Stream of Video and Audio AudioRack32 Rack The AudioRack32 has five main parts: AudioRack32 •Digital Audio Player—playsand records files in the .WAV format The Command Center The Command Center Controls The Command Center Display The Miniature Mode The Compact Disk Player The Compact Disk Player Controls The Audio Mixer The Audio Mixer Controls The Digital Audio Player The Digital Audio Player Controls The Digital Audio Player Display The MIDI Player The MIDI Player Controls The MIDI Player Display The Audio Recorder The Audio Recorder Controls The Audio Recorder Display Release Notes Disable Eject Button on the CD Player Using AudioRack CD Player as Default CD Player Configuring Playback Mixer The ASUS S370 CPU Card Using the ASUS S370 Setting up the ASUS S370 370Socket ASUS S370 Jumper Settings ASUS PCI-L101Fast Ethernet Card Features Software Driver Support Question and Answer Glossary Byte (Binary Term) COM Port CPU (Central Processing Unit) Device Driver DOS (Disk Operating System) MMX (Klamath) CPU as well as other PCI Bus (Peripheral Component Interconnect Local Bus) Peripherals POST (Power On Self Test) Ultra DMA/33 USB (Universal Serial Bus)