Asus V2-PE3 4.1Introduction, 4.2Motherboard layout

4.1Introduction

The Vintage V2-PE3 barebone system comes with an ASUS motherboard. This chapter provides technical information about the motherboard for future upgrades or system reconﬁguration.

4.2Motherboard layout

24.5cm (9.6in)

PS/2KBMS

T: Mouse

B: Keyboard

COM1			LGA775
			LGA775
	PARALLEL PORT
VGA
BOTTOM: TOP:
USB1	IE1394	ATX12V
USB2		ATX12V
USB2		ATXPWR
LAN_USB34		ATXPWR	VIA P4M800
LAN_USB34			PRO
Top:Rear Speaker Out CD
Center:			®
Side Speaker Out
Below:
Center/Subwoofer
		CR2032 3V
		Lithium Cell	AGP
		CMOS Power	AGP
	RTL8110S		PCI1
	RTL8110S		SB_PWR
			SB_PWR
	AUX		PCI2
	AUX		TSB43AB22A
			TSB43AB22A
		SPDIF_OUT	PCI3
		SPDIF_OUT	IE1394_1

ALC655

FP_AUDIO COM2

		CHA_FAN
CPU_FAN			Super
			Super
			I/O
DDR2 DIMM A1 (128 bit,240-pin module)	DDR2 DIMM B1 (128 bit,240-pin module)	DDR DIMM A1 (64 bit,184-pin module) DDR DIMM B1 (64 bit,184-pin module)	PRI IDE	SEC IDE	22.9cm (9.0in)
			BUZZER
			SATA2	FLOPPY
	VIA VT8237R			FLOPPY
	VIA VT8237R
		Plus	SATA1
			SATA1
			IR_CON
USB56		USB78 4Mb BIOS
			FWP CLRTC1 F_PANEL

4-2	Chapter 4: Motherboard info

Contents

Vintage V2-PE3 E2548 First Edition March Chapter 1:System Introduction Chapter 2:Basic Installation Chapter 3:Starting up Chapter 4:Motherboard Info Chapter 5:BIOS setup FederalCommunications Commission Statement Canadian Department of Communications Statement Electricalsafety Operation safety CLASS 1 LASER PRODUCT Audience How this guide is organized Conventions used in this guide Where to find more information System introduction 1.1Welcome Thank you for choosing the ASUS Vintage V2-PE3 The system supports up to 2 GB of system memory using 1.2Front panel Page 1.3Rear panel Audio 2, 4, or 6-channelconﬁguration Voltage selector 1.4Internal components Page Basic installation Basic components to install Tool 2.3Removing the side cover and front panel assembly 2.4.1 Overview 2.4.2 Installing CPU Page 2.4.3 Installing the CPU fan and heatsink assembly To install the CPU heatsink and fan: CPU_FAN CPU FAN Connector 2.5.1 Memory configurations DDR2 (533 MHz) Qualified VendorsList DDR (400 MHz) Qualified Vendors List DDR (333 MHz) Qualified Vendors List 2.5.2 Installing a DIMM 2.5.3 Removing aDIMM 2.6.1 Installing an expansion card 2.6.2 Configuring an expansion card Standardinterrupt assignments IRQ assignments for this motherboard 2.6.3 AGP slot 2.6.4 PCIslots 2.7Installing an optical drive Page 2.8Installing a hard disk drive Connect a -OR To install an IDE hard disk drive: 1.Follow steps 1-4of the previous section 2.9Installing a ﬂoppy disk drive To install a ﬂoppy disk drive: 1.Remove the front panel cover 3.Secure the ﬂoppy disk drive with two screws on both sides LED cables Page Starting up 3.1Installing an operating system 3.2Powering up Press the system power button () to enter the OS 3.3Support CD information Chapter 3: Starting up 3.3.1 Running the support CD ASUS InstAll- Drivers Installation Wizard VIA Chipset Driver Program VIA S3G Display driver Realtek ACʼ97 Audio Driver 3.3.2 Utilities menu ASUS InstAll -Installation Wizard for Utilities ASUS PC Probe ASUS Update ASUS Screen Saver 3.3.3 Make Disk VIA 32/64bit RAID Driver 3.3.4 ASUS Contact information ASUS PC Probe Installing PC Probe Launching PC Probe Using PC Probe Preferences Hardware monitor panels WMIbrowser DMIbrowser PCIbrowser Usage Configuring PC Probe infoMotherboard 4.1Introduction 4.2Motherboard layout 4.3Jumpers 1. Clear RTC RAM (CLRTC) To erase the RTC RAM: 1.Turn OFF the computer and unplug the power cord 2.Remove the battery FWP BIOS_WP 4.4Connectors 1. Floppy disk drive connector (34-1pin FLOPPY) Floppy Disk Drive Connector 2. SerialATA connectors (7-pin SATA1, SATA2) SATA Connectors 3IDEconnectors (40-1pin PRI_IDE,SEC_IDE) IDE Connectors 4. CPU and Chassis Fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) CHA_FAN FAN Connectors 5. USB connectors (10-1pin USB56, USB78) USB 2.0 Connectors 6. ATX power connectors (20-pin EATXPWR, 4-pin ATX12V) ATX Power Connectors 7. Internalaudio connectors (4-pin CD, 4-pin AUX) Internal Audio Connectors 8. Front panelaudio connector (10-1pin FP_AUDIO) Front Panel Audio Connector 9. Digitalaudio connector (4-1pin SPDIF_OUT) Digital Audio Connector 10. Serialport connector (10-1pin COM2) COM Port Connector 11 IEEE1394 port (10-1pin IE1394_1) (optional) IEEE 1394 Connector 12. Infrared Module connector (5-1pin IR_CON) Infrared Connector 13. System panelconnector (10-1pin PANEL) This connector supports several chassis-mountedfunctions •System power LED (2-pinPWRLED) •Harddisk drive activity (2-pin HDLED) •Power/Soft-offbutton (2-pinPWRBTN) BIOS setup 5.1.1 Creating a bootable floppy disk 5.1.2 ASUS EZ Flash utility 5.1.3 Award BIOS Flash Utility P5VDCTVM Boot the system in DOS mode using the bootable ﬂoppy disk you created earlier 7.Press <N> when the utility prompts you to save the current BIOS ﬁle 5.1.4 Saving the current BIOS file 5.1.5 ASUS CrashFree BIOS 2 utility Recovering the BIOS from a floppy disk 5.2BIOS setup program Legend box List box Sub-menu Date [Day, xx/xx/xxxx] Time [xx:xx:xx] IDEChannel0 Master/Slave IDEChannel1 Master/Slave IDE HDD Auto-Detection[Press Enter] Allows auto-detectionof the hard disk driveʼs speciﬁcations IDE Channel 0, 1 Master/Slave [Auto] Sets the selected channel as Master or Slave Conﬁguration options: [None] [Auto] [Manual] SATA Channel2, 3 Master Drive A/B [1.44M, 3.5 in.] t On CPU Feature [Press Enter] Hard Disk Boot Priority [Press Enter] First/Second/Third Boot Device Boot Other Device [Enabled] Boot Up Floppy Seek [Disabled] Boot UP Num-LockStatus [On] Security Option [Setup] Onchip IDEDevice IDEPrimary, Secondary Master/Slave PIO [Auto] IDEPrimary, Secondary Master/Slave UDMA [Auto] Onboard Device Onboard 1394 [Enabled] USB Controller [Enabled] USB 2.0 Controller [Enabled] USB Keyboard Support [Enabled] Onboard LAN Device [Enabled] Onboard LAN Boot ROM [Disabled] SuperIO Device Onboard SerialPort 1 [3F8/IRQ4] Onboard SerialPort 2 [2F8/IRQ3] ParallelPort Mode [ECP] UART Mode Select [Normal] ECP Mode Use DMA [3] ACPIFunction [Enabled] ACPISuspend Type [S3(STR)] Off by Power Button [I nstant-Off] Resume by PCIPME[Disabled] Resume by Ring [Enabled] Resume by USB (S3) [Enabled] Resume by Alarm [Disabled] Day of Month Alarm [NA] Time (hh:mm:ss) Alarm [0 :0 :0] CPU Temperature [xxxºC] MB Temperature [xxxºC] CPU Fan Speed [xxxxRPM] System Fan Speed [xxxxRPM] VCOREVoltage, 3V Voltage, +5V in, +13V in Load Optimized Defaults Supervisor Password User Password Save & Exit Setup Exit Without Saving