Manuals / Brands / Communications / Telephone / AT&T / Communications / Telephone

AT&T RCU450, 8102 Labeling the Programmable Dialing Button Designation Card, Removing and Covering the Auto Answer Button

1 45

Download 45 pages, 697.04 Kb

Labeling the Programmable Dialing Button Designation Card

Use the following directions for labeling and inserting the programmable

dialing buttons designation card on your telephone.

Note: For directions on storing numbers on the programmable dialing

buttons, refer to "Programmable Dialing Buttons" in the section titled

Using the Features.

1In the blank space next to the appropriate Programmable Dialing

button, write or type the name, telephone number, or dialed feature

that you want to store there.

2Fold along the perforated edge(s) and detach the card(s) from the

sheet.

3Remove the plastic cover by placing your finger in the finger slot on

the right side of the telephone and lifting up.

Removing and Covering the Auto Answer Button

If you are have an 8110 telephone, you may want to disable the Auto

Answer button ([ Auto ]) so that it cannot be activated accidentally.

Follow this procedure to remove the Auto Answer button and cover the

opening from which you removed the button.

Note: To complete this procedure, you will need the slot cover which is

shipped in the box with the telephone. You may also need a pair of

needlenose pliers.

Place the designation card on the telephone. Replace the plastic

cover over the designation card by fitting the cover's bottom tabs into

the slots on the telephone and pressing down, allowing the tabs on

the top to snap into place. See Figure 10.

1

2

3

FIGURE 10 Removing the Plastic Cover; Installing the Button Designation Card

Press [ Auto ] so that the button is in the "up" position

Lift the button from its slot on the face of the telephone. (You will

probably want to use a set of needlenose pliers for this task.)

See Figure 11.

Take the slot cover (provided with the telephone) and place it in a

horizontal position in the empty slot. See Figure 11. Be sure that

the cap is snug with the face of the telephone.

4

18 19

Contents

Main Page Contents Important Safety Instructions Contents Important Safety Instructions Service AT&T 4-type protectors, except the 4C3S-75 "Enhanced" Protector SAVE THESE INSTRUCTIONS CONSIGNES DE SECURITE IMPORTANTES Emploi 3 2 Service AT&T 4-type protectors, except the 4C3S-75 "Enhanced" Protector CONSIGNES DE SECURITE IMPORTANTES Emploi 3 2 Entretien AVERTISSEMENT: CONSERVEZ CES INSTRUCTIONS Your 8102 and 8110 Telephones Entretien AVERTISSEMENT: 5 CONSERVEZ CES INSTRUCTIONS Your 8102 and 8110 Telephones Page Page Page Page Page Page Installing Your Telephone Table/Desk Installation 12 13 Installing Your Telephone Table/Desk Installation 12 13 Page Wall Installation Page 16 17 Labeling the Programmable Dialing Button Designation Card Removing and Covering the Auto Answer Button 18 19 Labeling the Programmable Dialing Button Designation Card Removing and Covering the Auto Answer Button 18 19 Using the Features Using the Handset and Speakerphone 21 Answering and Placing a Call To answer a call Using the Features Using the Handset and Speakerphone 21 Answering and Placing a Call To answer a call Auto Answer (for 8110 Users) To have your telephone automatically answer a call To turn off the Auto Answer feature 22 Answering and Placing a Call (cont.) To place a call using the speakerphone (for 8110 users) Auto Answer (for 8110 Users) To have your telephone automatically answer a call To turn off the Auto Answer feature 22 Flash Hold 25 24 To put a call on hold Flash Hold 25 24 To put a call on hold Personalized Ring Programmable Dialing Buttons 27 26 Personalized Ring Programmable Dialing Buttons 27 26 To erase a number stored on a programmable dialing button Redial (With Auto-Pause) To automatically redial the last number dialed from the dial pad To erase ALL stored access codes 28 To erase a number stored on a programmable dialing button Redial (With Auto-Pause) To automatically redial the last number dialed from the dial pad To erase ALL stored access codes 28 Speakerphone (for 8110 Users) Appendix A Adjunct Equipment Installation Instructions (For the 8102 Telephone Only) Speakerphone (for 8110 Users) To place/answer a call without lifting the handset 31 Appendix A Adjunct Equipment Installation Instructions (For the 8102 Telephone Only) Appendix B Operation of the 500A Headset Adapter (with the 8102 Telephone) Answering Calls Originating Calls Putting Calls on Hold Appendix B Operation of the 500A Headset Adapter (with the 8102 Telephone) Answering Calls Originating Calls Putting Calls on Hold Appendix C Auxiliary Power for the 8110 Telephone Switching from the Headset to the Handset Appendix C Auxiliary Power for the 8110 Telephone Appendix DFCC Registration and Repair Information If Your Telephone Does Not Respond 37 36 CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK Appendix DFCC Registration and Repair Information If Your Telephone Does Not Respond 37 36 CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK Interference Information AT&T Warranty Information Interference Information AT&T Warranty Information Quick Reference Guide Storing Numbers in Memory Dialing Numbers in Memory Erasing a Number in Memory Holding and Returning to a Call Using the Built-in Speakerphone (For 8110 Users Only) Using the Auto Answer Feature (For 8110 Users Only)