AT&T RCU450, 8102 Appendix B

Power

supply Adjunct

cord

Adjunct

power cord

Adjunct

(equipment)

jack S201A

Speakerphone

(Top view)

Line jack

Adjunct

power jack

8102 Voice Terminal

(Bottom view)

FIGURE 12 Connecting Adjunct Equipment and an Adjunct Power Supply to

an 8102 Telephone

32

Appendix B

Operation of the 500A Headset Adapter

(with the 8102 Telephone)

If you are using a 500A Headset Adapter with your 8102 telephone, read

the following instructions on using a headset and the headset adapter.

Note that headset operation is essentially the same as handset

operation, except when using the Hold feature.

Answering Calls

When a 500A headset adapter is connected to the Adjunct jack of an

8102 telephone, you may answer calls with either the handset or headset

adapter.

To answer a call with the headset adapter, press the On/Quiet button.

(The green light next to the button goes on.)

To mute the handset or headset adapter, you must hold down the

On/Quiet button. (The green light next to the button stays on for as long

as the button is held down.) When you want the other party to hear you

again, you can remove your finger from the On/Quiet button. (The light

goes off.)

To end a call, press the Off button on the headset adapter.

Originating Calls

To go off-hook to place a call press the On/Quiet button and dial the

number using the dial pad, [ Redial ], or the appropriate programmable

dialing button. [ Flash ] works the same with a headset adapter as it would

with a handset.

Putting Calls on Hold

To put a call on hold, press the Hold button on the 8102 telephone.

(Note that the green light next to the On/Quiet button on the headset

adapter remains on, even though the call is on hold.)

To retrieve the call on hold, you must press the Off button, and then

within 2 seconds, press the On/Quiet button. (The red Hold light on the

8102 telephone goes off.) If you take more than 2 seconds for this

sequence of button presses, the call will be dropped.

33

Contents

Main Page Contents Important Safety Instructions Contents Important Safety Instructions Service AT&T 4-type protectors, except the 4C3S-75 "Enhanced" Protector SAVE THESE INSTRUCTIONS CONSIGNES DE SECURITE IMPORTANTES Emploi 3 2 Service AT&T 4-type protectors, except the 4C3S-75 "Enhanced" Protector CONSIGNES DE SECURITE IMPORTANTES Emploi 3 2 Entretien AVERTISSEMENT: CONSERVEZ CES INSTRUCTIONS Your 8102 and 8110 Telephones Entretien AVERTISSEMENT: 5 CONSERVEZ CES INSTRUCTIONS Your 8102 and 8110 Telephones Page Page Page Page Page Page Installing Your Telephone Table/Desk Installation 12 13 Installing Your Telephone Table/Desk Installation 12 13 Page Wall Installation Page 16 17 Labeling the Programmable Dialing Button Designation Card Removing and Covering the Auto Answer Button 18 19 Labeling the Programmable Dialing Button Designation Card Removing and Covering the Auto Answer Button 18 19 Using the Features Using the Handset and Speakerphone 21 Answering and Placing a Call To answer a call Using the Features Using the Handset and Speakerphone 21 Answering and Placing a Call To answer a call Auto Answer (for 8110 Users) To have your telephone automatically answer a call To turn off the Auto Answer feature 22 Answering and Placing a Call (cont.) To place a call using the speakerphone (for 8110 users) Auto Answer (for 8110 Users) To have your telephone automatically answer a call To turn off the Auto Answer feature 22 Flash Hold 25 24 To put a call on hold Flash Hold 25 24 To put a call on hold Personalized Ring Programmable Dialing Buttons 27 26 Personalized Ring Programmable Dialing Buttons 27 26 To erase a number stored on a programmable dialing button Redial (With Auto-Pause) To automatically redial the last number dialed from the dial pad To erase ALL stored access codes 28 To erase a number stored on a programmable dialing button Redial (With Auto-Pause) To automatically redial the last number dialed from the dial pad To erase ALL stored access codes 28 Speakerphone (for 8110 Users) Appendix A Adjunct Equipment Installation Instructions (For the 8102 Telephone Only) Speakerphone (for 8110 Users) To place/answer a call without lifting the handset 31 Appendix A Adjunct Equipment Installation Instructions (For the 8102 Telephone Only) Appendix B Operation of the 500A Headset Adapter (with the 8102 Telephone) Answering Calls Originating Calls Putting Calls on Hold Appendix B Operation of the 500A Headset Adapter (with the 8102 Telephone) Answering Calls Originating Calls Putting Calls on Hold Appendix C Auxiliary Power for the 8110 Telephone Switching from the Headset to the Handset Appendix C Auxiliary Power for the 8110 Telephone Appendix DFCC Registration and Repair Information If Your Telephone Does Not Respond 37 36 CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK Appendix DFCC Registration and Repair Information If Your Telephone Does Not Respond 37 36 CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK Interference Information AT&T Warranty Information Interference Information AT&T Warranty Information Quick Reference Guide Storing Numbers in Memory Dialing Numbers in Memory Erasing a Number in Memory Holding and Returning to a Call Using the Built-in Speakerphone (For 8110 Users Only) Using the Auto Answer Feature (For 8110 Users Only)