Manuals / AT&T / Communications / Cordless Telephone

AT&T 9341 Replacing the Handset Battery Pack, Lift out the old battery pack and disconnect

Models: 9341

1 26

Download 26 pages 18.2 Kb

Page 24

Replacing the Handset Battery Pack

9341_book_1ATT 6/14/00 4:07 PM Page 22

BATTERIES

Nickel-Cadmium Rechargeable Batteries must be recycled or disposed of properly. Do not dispose of in household garbage. If burned, it could explode. If punctured, it could release caustic material which could injure the skin or eyes. If swallowed, it may be toxic.

The RBRC™ seal means that the manufacturer is voluntarily participating in an industry program to collect and recycle Nickel-Cadmium rechargeable batteries when taken out of service within the United States. These batteries may be taken to a participating local retailer of replacement batteries or recycling center. Or, you may call 1 800 8BATTERY for locations accepting spent Nickel-Cadmium batteries.

Replacing the Handset Battery Pack

1Remove the battery compartment cover on the handset by pressing on the indentation and sliding the cover downward.

2Lift out the old battery pack and disconnect.

3Align the two holes in the new battery pack’s plug with the socket pins, and snap the plug into place. Place the battery pack in the compartment with the wires in the lower left corner, along the bottom of the battery pack.

4Replace the cover by sliding it up into place.

5The new battery pack must be charged before using the phone. Place the handset in the base and allow it to charge for at least

16 hours the first charge. The telephone might operate before that, but for best performance, let the battery pack charge fully.

RBRC is a registered trademark of the Rechargeable Battery Recycling Corporation.

22

Image 24

AT&T 9341 user manual Replacing the Handset Battery Pack, Lift out the old battery pack and disconnect, Batteries

Contents

900 MHz Cordless Telephone with Caller ID/Call Waiting Part 1 - Important Product InformationREVISED 6/14/00 USER’S MANUALPrinted in China. XXXXXXXX Issue 1AT&T 5/00 2000 Advanced American Telephones. All rights reserved9341book1ATT 6/14/00 407 PM Page BEFORE YOU BEGIN CONTENTSFEATURE SETTINGS INSTALLATION9341book1ATT 6/14/00 407 PM Page BEFORE YOU BEGIN About Caller Identification Caller IDINSTALLATION Before You Install2 Install the handset battery Table/Desk Installation 1 Connect the telephone line cord 2 Connect the power cord3 Attach belt clip to the cordless handset optional To attachWall Installation 3 Charge the handset battery4 Check for dial tone 5 Set the dial mode2 Connect the telephone line cord 3 Connect the power cord 5 Follow Steps 3-5 in Table/Desk Installation4 Mount the base on the wall Align holes onFEATURE SETTINGS Time/DateRinger Selection Auto Answer On/OffHandset Volume Exit programming Cancel a pageTELEPHONE OPERATION Answer a Callwaiting signal when you havewhen handset If you subscribeTemporary Tone Dialing Headset JackTELEPHONE OPERATION Operating Range Display Screen MessagesScreen Displays WhenTELEPHONE MEMORY Store Memory NumbersPresses Edit Numbers Stored in Memory Delete Numbers Stored in MemoryMove Numbers Stored in Memory Delete a Specific NumberDial Memory Numbers TELEPHONE MEMORY1 Press P 2 Press M, then enter the memory location 3 Press PCALLER ID OPERATION About Call HistoryReview Call History Indicates number of times this party has called Caller’s nameDelete Call History Dial a Displayed NumberDelete a Specific Call Delete All CallsStore Call in Memory CALLER ID OPERATIONCall Block Turn Off Call BlockCALLER ID OPERATION PRIVATE NAME PRIVATE CALLERUNKNOWN NAME UNKNOWN CALLERCharging the Handset Battery Pack BATTERIESReplacing the Handset Battery Pack 2 Lift out the old battery pack and disconnectBATTERIES If you hear a two-beep signal when you try to use the handset If the phone does not ring when you receive a callIN CASE OF DIFFICULTY If the phone doesn’t work at all, check these items firstIf you hear noise or interference when using the phone If you hear other calls while using your phoneIf you lose a call after changing channels IN CASE OF DIFFICULTY