Manuals / AT&T / Communications / Cordless Telephone

AT&T 9341 Operating Range, Display Screen Messages, Screen Displays, When, Telephone Operation

Models: 9341

1 26

Download 26 pages 18.2 Kb

Page 14

Operating Range

9341_book_1ATT 6/14/00 4:07 PM Page 12

TELEPHONE OPERATION

Operating Range

This cordless telephone operates within the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, keep the base antenna fully upright.

If you receive a call while you are out of range, the handset might not ring — or if it does ring, the call might not connect when you press P. Move closer to the base, then press Pto answer the call.

If you move out of range during a phone conversation, you might hear noise or interference. To improve reception, move closer to the base.

If you move out of range without pressing O, your phone will be left “off the hook.” To hang up properly, walk back into range, periodically pressing O.

Display Screen Messages

Screen Displays:	When:
STANDBY	The handset is not in use.
NO LINE	The base is not connected to the telephone line,
	or the line is not working.
RINGING	There is a call coming in.
CONNECTING	The handset is waiting for a dial tone.
PHONE ON	The handset is in use.
MESSAGE WAITING	You have received telephone company voice mail.
PAGING	The base is paging the handset.

12

Image 14

AT&T 9341 user manual Operating Range, Display Screen Messages, Screen Displays, When, Telephone Operation

Contents

REVISED 6/14/00 900 MHz Cordless Telephone with Caller ID/Call WaitingPart 1 - Important Product Information USER’S MANUAL9341book1ATT 6/14/00 407 PM Page Printed in China. XXXXXXXX Issue 1AT&T 5/002000 Advanced American Telephones. All rights reserved FEATURE SETTINGS BEFORE YOU BEGINCONTENTS INSTALLATION9341book1ATT 6/14/00 407 PM Page BEFORE YOU BEGIN About Caller Identification Caller ID2 Install the handset battery INSTALLATIONBefore You Install 3 Attach belt clip to the cordless handset optional Table/Desk Installation1 Connect the telephone line cord 2 Connect the power cord To attach4 Check for dial tone Wall Installation3 Charge the handset battery 5 Set the dial mode4 Mount the base on the wall 2 Connect the telephone line cord 3 Connect the power cord5 Follow Steps 3-5 in Table/Desk Installation Align holes onRinger Selection FEATURE SETTINGSTime/Date Auto Answer On/OffTELEPHONE OPERATION Handset VolumeExit programming Cancel a page Answer a Callwhen handset waiting signalwhen you have If you subscribeTELEPHONE OPERATION Temporary Tone DialingHeadset Jack Screen Displays Operating RangeDisplay Screen Messages WhenPresses TELEPHONE MEMORYStore Memory Numbers Move Numbers Stored in Memory Edit Numbers Stored in MemoryDelete Numbers Stored in Memory Delete a Specific Number1 Press P 2 Press M, then enter the memory location Dial Memory NumbersTELEPHONE MEMORY 3 Press PReview Call History CALLER ID OPERATIONAbout Call History Indicates number of times this party has called Caller’s nameDelete a Specific Call Delete Call HistoryDial a Displayed Number Delete All CallsStore Call in Memory CALLER ID OPERATIONCALLER ID OPERATION Call BlockTurn Off Call Block UNKNOWN NAME PRIVATE NAMEPRIVATE CALLER UNKNOWN CALLERCharging the Handset Battery Pack BATTERIESBATTERIES Replacing the Handset Battery Pack2 Lift out the old battery pack and disconnect IN CASE OF DIFFICULTY If you hear a two-beep signal when you try to use the handsetIf the phone does not ring when you receive a call If the phone doesn’t work at all, check these items firstIf you lose a call after changing channels If you hear noise or interference when using the phoneIf you hear other calls while using your phone IN CASE OF DIFFICULTY