Manuals / Atlantis Land / Computer Equipment / Network Router

Atlantis Land ATLMMR MNE01 user manual Make sure baud rate is 19200,n, 8,1,none, Answer

Models: ATLMMR MNE01

1 39

Download 39 pages 16.59 Kb

Page 38

2.Make sure baud rate is 19200,n, 8,1,none

3.Turn off the Router, and connect the Console Port Cable.

4.Turn on the Router.

5.Press Ctrl+C while the message “Loading Firmware” shows up.

6.Then it will show “Clearing System Configuration” once the system is ready.

7.Therefore, it will recover the default password while the router reboot automatically.

Why does the ISDN Router connect with ISP sometimes automatically?

Answer.

The Router will build up connected function once LAN’s PC has any packet need to send . This function calls Dial on Demand.

Why didn’t the router offline automatically even my Idle Time exceeded?

Answer.

There are several reasons for in-completed offline:

1.The setting Idle time is greater than the confirmed connection packet from ISP.

2.If there is any packet flow into the LAN, Idle Time will always recalculated.

3.LAN’s PC is running Program for the Network, And Program send the packet to the Internet.

You could use the window in Show Profile Status to monitor the packet quantity in Network.

Why can’t I connect successfully while I use Remote Dial-in?

Answer.

Please be sure both Remote User’s Username and password are correct, and keep the setting information identically at two sides of Router. The best way is setting the Router in MultiPPP.

35

Image 38

Atlantis Land ATLMMR MNE01 user manual Make sure baud rate is 19200,n, 8,1,none, Answer

Contents

User’s Manual with 10/100 LAN portISDN Router SUPPORT COPYRIGHTDISCLAIMER AtlantisLand spaTable of Contents Introduction 1.2 Package contentsChapter 1.1 An overview of the ISDN Router1.3 ISDN Router Features 1.4 ISDN Router Application2.2 The front LEDs Using the ISDN Router2.1 Cautions for using the ISDN Router PowerPower 2.3 The rear ports2.4 Cabling connectorPage Configuring PC in Windows 95/98/ME Configuration3.1 Before Configuration Chapter4. Then select the DNS Configuration tab 3. Select the Obtain an IP address automatically radio buttonConfiguring PC in Windows NT4.0 2. Select TCP/IP Protocol and click Properties4. Select Internet Protocol TCP/IP and click Properties Configuring PC in Windows3. In the Local Area Connection Status window click Properties 5. Select the Obtain an IP address automatically and the 3.2 Configuring with GUI program3.2.1 Using Different Browsers for ISDN Router Netscape Navigator3.2.3 Customize User Interface 3.2.2 Password3.2.4 Basic Internet Access Configuration 3.2.5 Internet Access with Advanced Configuration Step 5 Click Apply and TestStep 4 Enter the following information Step 2 Select the ISDN switch type that your ISP will tell youISP Account Password the password of your ISP account Remote Phone Number the ISDN telephone number of your ISPStep 2 The Advanced Internet Access Setup screen appears 3.2.6 IP Configuration for Internet AccessOne B Channel Only Two B Channels Only When Needed Always two B Channels3.2.7 The IP Routing Table Set the following parametersStep 2 Enter the following information 3.2.8 IP Address Translation Configuration Step 3 Click APPLY3.2.9 Add or Edit IP Address Translation Step 4 Click Apply Delete a Set of IP Address Translation 3.2.10 Static DHCP ConfigurationAdd or Edit a Set of static private IP address Step 2 Click EditStep 2 Click Delete Delete a Set of static private IP addressStep 3 Click Apply Chapter Remote Configuration4.1 Remote Office Access by ISDN Remote Phone Number My System Name My System Password Remote System Password 4.2 Advanced Options for Remote Office Access ProfilesSystem Name and My System Password Remote System Name Remote Sub-AddressEnable IP IP RIP Remote IP Address Remote IP Netmask Enable Bridging 4.3 Deleting Remote Office Access Profile Step 1 Select Connection Profiles in the Menu WindowChapter Dial-in User Access Configuration5.1 Configuring a Dial-in User Profile Step 4 Enter the information of screen Step 6 Enter the informationStep 1 Select Connection Profiles from the Menu Window 5.2 Deleting Dial-in User Profiles5.3 Packet Filtering Page Management 6.1 How to Upgrade the Firmware6.2 How to Reset ChapterCurrent Password New Password Confirm Password Step 3 Click Submit 6.3 How to Change ISDN Router Manager Password6.4 What if I Forget the Password? How do I set up the Idle Time? TroubleshootingWhat is NAT? ChapterWhy can’t I use ICQ software under the device? Why does the configuration lost from previous usage?Why do I spend longer time to update firmware in GUI screen? What’s Data over Voice Channel?Solution Why can’t I set up IP Filter function in GUI?Solution For example, set IP LAN to 202.39.52.1902. Make sure baud rate is 19200,n, 8,1,none Why does the ISDN Router connect with ISP sometimes automatically?Why can’t I connect successfully while I use Remote Dial-in? Answer Answer