Atlas MLGS180W, MLGS180B manual Troubleshooting Guide, Five Year Limited Warranty

TROUBLESHOOTING GUIDE

If you experience a problem with your Light Control, first follow this guide. For additional assistance write to: Atlas Lighting Products, Inc. • Customer Service Department • P.O. Box 2348 • Burlington, NC 27216

SYMPTOM	POSSIBLE CAUSE
Lights will not	1.	Light switch is turned off.
come on.	2. Light is loose or burned out.
	3.	Fuse is blown or circuit breaker is turned
		off.
	4.	Daylight turn-off is in effect (recheck
		after dark).
	5.	Incorrect circuit wiring, if this is a new
		installation.
	6.	Re-aim the sensor to cover desired area.
Lights come on	1.	Light Control may be installed in a rela-
in daylight.		tively dark location.
	2.	Light Control is in Test. (Set control
		switch to an ON-TIME position).
Lights come on for	1. Light Control may be sensing small
no apparent rea-		animals or automobile traffic (re-aim
son.		sensor).
	2.	Range is set too high. (Reduce Range).

SYMPTOM	POSSIBLE CAUSE
Lights stay on	1. A lamp is positioned too close to the sensor
continuously.		or pointed at nearby objects that cause heat
		to trigger the sensor. (Reposition the lamp
		away from the sensor or nearby objects).
	2.	Light Control is pointed toward a heat
		source like an air vent, dryer vent, or
		brightly-painted heat-reflective surface.
		(Reposition sensor).
	3.	Light Control is in Manual Mode. (Switch
		to Auto.)
Lights flash on	1. Heat or light from the lamps may be turn-
and off.		ing the Light Control on and off. (Reposi-
		tion the lamps away from the sensor).
	2.	Heat being reflected from other objects may
		be affecting the sensor. (Reposition sensor).
	3.	Light Control is in the Test mode and
		warming up. (Flashing is normal under
		these conditions).
	4.	Light Control is detecting a light source.
		(Reposition Light Control or lamp).
Lights flash	1.	Sensor is detecting its own lights. (Repo-
once, then stay		sition lamps to keep area below the sen-
off in Manual		sor relatively dark.)
Mode.

FIVE YEAR LIMITED WARRANTY

Atlas Lighting Products, Inc. warrants against defects in materials or workmanship for a period of five years from the date of purchase for use, and agrees to repair or, at our option, replace a defective unit without charge for either parts or labor. IMPORTANT: This warranty does not cover damage resulting from accident, misuse of abuse, lack of reasonable care, the affixing of any attachment not provided with product, alteration of any attachments factory installed, loss of parts or subjecting the fixture to any but the specified electrical service. This warranty does not cover failure of the bulb due to accidents, abuse, misuse, vandalism, power surges, and acts of nature such as lightning damage. No responsibility is assumed for any special incidental or consequential damages. Damages occurring during transit are not covered by this warranty-including UPS shipments. To obtain warranty service, mail sales receipt as proof-of-purchase, date and a brief explanation of the nature of the defect, to the address listed below. You will receive, by mail, a Return Goods Authorization number and full instructions for returning defective merchandise. All returned goods must be accompanied by a Return Goods Authorization number issued by Atlas Lighting Products, Inc.

NOTE: No other warranty, written or verbal, is authorized by Atlas Lighting Products, Inc. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion and limitations may not apply to you.

For information regarding replacement parts please write to:

Atlas Lighting Products, Inc.

Attn: Customer Service Department

P.O. Box 2348

Burlington, NC 27216

-4- 598-1096-01