AT91CAP7X-DK Development Kit

for CAP Customizable Microcontroller

AT91CAP7X Features

n160 KB of fast on-chip SRAM

nA large MP Block of 450K ASIC gates (2-input NAND equivalents)

nMicro Core = ARM7TDMI® at 80 MHz

nMPRAM = 2x DPRAM 2K x 16

nROM = 256 KB

nA minimal number of ARM peripherals are instantiated in the fixed portion of the design to address low cost applications

nFlexibility to instantiate other peripherals in the MP Block using IP available in Atmel's vast library

The CAP Customizable Microcontroller

Atmel’s CAP is an ARM microcontroller-based system-on-chip with fast local memory, a wide range of industry standard peripherals and interfaces, and a Metal Programmable (MP) Block that allows the designer to add custom logic. By combining the performance, density and low power consumption of the fixed portion of the device with the flexibility of the MP Block, CAP enables application-specific products to be developed in a fraction of the time and at a fraction of the cost of standard-cell ASICs, but at a unit price close to that of standard cell devices. CAP also offers superior performance, smaller form factor and lower power consumption at a unit price significantly lower than an MCU-plus-FPGA combination for the same functionality.

Headquarters

Atmel Corporation

2325 Orchard Parkway

San Jose, CA 95131

USA

Tel 1 (408) 441-0311

Fax 1 (408) 487-2600

International

Atmel Asia

Room 1219

Chinachem Golden Plaza

77 Mody Road Tsimshatsui

East Kowloon

Hong Kong

TEL (852) 2721-9778

FAX (852) 2722-1369

Atmel Europe

Le Krebs

8, Rue Jean-Pierre Timbaud

BP 309

78054 St.-Quentin-en-Yvelines

Cedex, France

Tel: (33) 1-30-60-70-00

Fax: (33) 1-30-60-71-11

Atmel Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

Japan

TEL (81) 3-3523-3551

FAX (81) 3-3523-7581

Product Contacts

Technical Support www.atmel.com/products/AT91CAP

Sales Contacts

www.atmel.com/contacts

Web Site

www.atmel.com

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

© 2008 Atmel Corporation. All rights reserved.

Atmel®, logo and combinations thereof, and others, are registered trademarks, CAP™ and others are trademarks of Atmel Corporation or its subsidiaries. ARM® and ARM7TDMI® are registered trademarks of ARM Ltd. Other terms and product names may be trademarks of others.

REV.: 8522A-03/08

Page 2
Image 2
Atmel AT91CAP7X-DK manual AT91CAP7X Features, CAP Customizable Microcontroller, Headquarters, Usa