Attwood 4201, 69317, 4061, 4030 Installation Instructions, Wiring Instructions For Manual Operation

4. Connect the spliced leads to the ÓManualÓ terminal of the three-way switch.

3. Inspect impeller chamber and motor shaft behind impeller. Remove any

Important:

¨

foreign objects.

Although3the switch is submersible, the lead wires must terminate in a waterproof connection. Mount wires above the highest possible water mark

toHeavyprevent electrolysisDutydamage to theBilgeboat. Pump

5. With three-way switch on AUTO, test float switch by gently raising the

float4030,. Pump4060,should activate4031,with4061float up, and deactivate with float down. See figure 4

Installation Instructions

6.Test pump by ensuring that pump turns on when water level is above float switch,Attwoodandmarineshutshardware,off when watern vigationallevel is lighting,pumpedbilgebelowpumps,float switchand other. Cycle themarinepumpaccessorieswith water inarethespecifiedbilge severalmore thantimesanyto ensuotherebrandthat theby systemAmericaÕsis

functioningbest-knownproperlyboat manufacturers.as original equipment. Look to Attwood for

quality replacement parts and marine accessories. Figure 5

SAVE THESE INSTRUCTIONS

4.	Inspect ÒOÓ ring on lower chamber for nicks, cuts or other damage. Apply a
	light coat of petroleum jelly to ÒOÓ ring surface.
5.	Assemble chamber into motor housing. Ensure ÒOÓ ring is in retaining
	groove and alignment pin is in pin receptacle next to locking button.
6.	Install and tighten retaining screws.
7.	Attach motor housing to pump base by aligning four retaining tabs and
	twisting clockwise until lock button snaps into place.

Form Number 69317 Rev. D

2-Way Switch On/Off

HD 1700: 10 Amp Rating

HD 2000: 12 Amp Rating

On ¥¥

¥ ¥ Off

Brown Wire

¥¥ HD 1700: 10 Amp Fuse HD 2000: 12 Amp Fuse

¥ Ð +

Black Wire

03/10

¥

¥

72" (183mm) Maximum Length From (+) Terminal To Fuse Holder

¥

12 Volt Battery

WIRING INSTRUCTIONS FOR MANUAL OPERATION

1.Splice suitable lengths of brown and black 16-gauge wire to existing pump wiring, enough to reach ON/OFF/ switch and battery.

2.Using insulated terminal connectors, connect positive lead (brown) to the ON/OFF switch. Connect negative lead (black) to ground.

3.In a location easily accessible for changing fuses, splice fuse holder into positive lead (brown). The fuse holder must be installed within 72" (183 cm) of the positive (+) battery terminal.

4.To check system, feed water into the pump. If flow appears to be too low, make sure wires have been connected properly: brown-to-positive (switch), and black-to-negative.

Figure 6

	L
	O
	C
	K
	Impeller
¥	¥ Motor Housing
	¥
	Locking Button

¥O-Ring

¥Pump Chamber

CLEANING INSTRUCTIONS

1.To remove the motor housing from base: Depress the locking button and twist motor housing counter-clockwise.

2.Remove three retaining screws that attach pump chamber to motor housing. Remove chamber.

ATTWOOD HEAVY DUTY BILGE PUMP LIMITED WARRANTY:

ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331, (ÔAttwoodÕ) warrants to the original consumer purchaser that this Attwood Bilge Pump will be free from defects in materials and workmanship under normal use and service for:

Recreational/Pleasure Boats Ñ A period of three (3) years from the date of original consumer purchase.

Commercial Boats Ñ A period of one (1) year from the date of original consumer purchase.

This warranty does not extend to any batteries or fuses used with the pump. This limited warranty is not applicable if the bilge pump has been damaged by accident, improper installation, unreasonable use, lack of proper maintenance, unauthorized repairs or modifications, or other causes not arising out of defects in materials or workmanship. AttwoodÕs obligations under this warranty are limited to repair of the product at AttwoodÕs plant or replacement of the product at AttwoodÕs option and at AttwoodÕs expense. Any expenses involved in the removal, reinstallation, or transportation of the product are not covered by this warranty. The product must be returned to AttwoodÕs plant at the address indicated above postage prepaid, with proof of original purchase including date. If Attwood is unable to replace the bilge pump and repair is not commercially practicable or cannot be timely made, or if the original consumer purchaser is willing to accept a refund in lieu of repair or replacement, Attwood may refund the purchase price, less an amount for depreciation. The acceptance by Attwood of any product returned or any refund provided by Attwood shall not be deemed an admission that the product is defective or in violation of any warranty.

THIS WARRANTY IS ATTWOODÕS ONLY EXPRESS WARRANTY OF THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1) YEAR FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights which may vary from state to state.

© 2003 Attwood Corporation

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com