nApplications
The TI035 programmable wall switch has been designed to control lightings and motors:
Load type | Maximum load | Examples | ||
|
|
|
| |
| 2400 W | • | incandescent lights | |
Resistive load | • | halogen lights | ||
(20 A @ 120 V) | ||||
| • | block heater | ||
|
| |||
|
|
|
| |
|
| • | fluorescent lights | |
Inductive load | 2400 W | • | compact fluorescent lights (CFL) | |
(20 A @ 120 V) | • | sodium lamps | ||
| ||||
|
| • | electronic ballasts | |
|
|
|
| |
Motor | 1 hp | • | pool filter pumps | |
• | fans | |||
|
| |||
|
|
|
|
oInstallation
NOTE: This switch cannot be used if there are not at least 2 white wires joined by a connector inside the electrical box.
nCut power at the circuit breaker to avoid electric shock. o Remove the existing switch.
p Install the new switch as shown in the diagram below. q Apply power at the circuit breaker.
black white
blue
black
white
white (neutral)
120 VAC black (line)
TI035
Installation and User Guide
Programmable Wall Switch
Manual Mode
The programmable switch operates as a regular switch. Briefly press the switch door to turn the lights On or Off. The mode (MAN) and state (ON or OFF) are displayed.
Automatic Mode
The programmable switch follows the programmed
schedule. The mode (AUTO), state (ON or OFF) and current program number are displayed. To temporarily override the programmed schedule, briefly
press the switch door. The new state (ON or OFF) will flash
to show that the state is temporary. The override remains in effect until you press the switch door again or until the beginning of the next program.
rSetting the Clock
NOTE: The switch displays the time in
nTo switch between
a)Press one of the control buttons to ensure the MAN or AUTO indica- tor is displayed.
b)Press the MIN and HOUR buttons simultaneously and brieftly (0:00 display =
oSet the time using the HOUR and MIN buttons. For the
pPress one of the control buttons or close the switch door to return to normal operation.
sDaylight Savings Time
This procedure sets the switch for daylight savings time or for standard time.
nPress the CODE button four times.
oPress the MIN button to switch between nor and Ad.
nor | Standard time / Normal time / Winter time |
|
|
Ad | Daylight savings time / Advanced time / Summer time |
|
|
pPress one of the control buttons or close the switch door to return to nor- mal operation.
pPower-on
nPry the switch door open from the bottom using a small screwdriver.
oEnsure the ON/OFF selector is set to ON.
pReset the switch using a paper clip. 0:00
will flash.
If the display is blank:
•Ensure the ON/OFF selector is properly engaged in the ON position. Push it to the right using a small screwdriver.
Reset
Control (4)
On/Off selector
tSunset/Sunrise Program
NOTE: By default, once you have programmed the sunset/sunrise parameters, the timer will follow the sunrise/sunset program when placed in Automatic mode. To set your own schedule, see section 8.
7.1Determining the sunset/sunrise parameters
Fill out the following table:
Latitude | Longitude | Day # | nor/Ad | Lc |
|
|
|
|
|
|
|
|
|
|
1) LATITUDE & LONGITUDE: Enter the coordinates of your city or the |
nearest city using the supplied table. If none of the cities in the table is appli- |
qOperating Modes
The programmable switch has 2 operating modes: manual (MAN) and automatic (AUTO). To switch mode, press the switch door for 3 seconds.
cable, this information is usually available on the internet. |
NOTE: Add a minus sign when entering a south latitude coordinate or a west |
longitude coordinate. |
TI035 | 13/3/07 | 1/2 |