Aube Technologies TI035 manual Programming the Schedule, Troubleshooting, Technical Specifications

2)DAY #: Enter the day #. (Add the code of the current month to the current date.)

For example: For June 24th, the day # = 151 + 24 = 175

January	0	May	120	September	243
February	31	June	151	October	273
March	59	July	181	November	304
April	90	August	212	December	334

3)nor/Ad: If your country has daylight savings time, select the appropriate period.

nor	Standard time / Normal time / Winter time
Ad	Daylight savings time / Advanced time / Summer time

4)Lc: If your city’s time zone is based on political or economic boundaries instead of its coordinates, your lights might switch On/Off too early or too late with respect to sunrise and sunset. Therefore, apply a correction factor (+1 or -1). Otherwise, leave it at 0.

7.2Programming the sunset/sunrise parameters

Once you have completed section 7.1, proceed as follows:

nPress the CODE button until the desired parameter appears. The param- eters appear in the following order.

Parameter	Default	Possible	Buttons
	setting	settings	used
Latitude (LAT)	00	-65 to 65	HOUR & MIN
Longitude (LONG)	000	-180 to 180	HOUR & MIN
Day number (DAY #)	000	1 to 365	HOUR & MIN
Daylight savings time	nor	nor / Ad	MIN
Local correction factor (Lc)	0	-1, 0, 1	MIN

oPress the HOUR or MIN button to modify the value (see table above for the buttons to use).

pPress one of the control buttons or close the switch door to return to nor- mal operation.

uProgramming the Schedule

NOTE: This section allows you to set your own schedule.

The switch can hold 2 programs which are repeated every day. When you place the timer in Automatic mode, it will activate the load at the start of each program and deactivate it at the end of the program. You need to set the fol- lowing parameters:

P1 ON	: Start time of program 1
P1 OFF	: End time of program 1
P2 ON	:	Start time of program 2
P2 OFF	:	End time of program 2

nPress the PGM button until the desired parameter is displayed.

If you have entered your city’s parameters (see section 7), the parameters P1 ON and P2 OFF show the sunset time and sunrise time for this time of the year. If the timer is used for lighting, when placed in AUTO mode, it will turn the light ON at sunset and will turn it Off at sunrise. For example:

P1 ON		:	20:38 (sunset)
P1	OFF	: --:--(blank)
P2	ON	: --:--(blank)
P2 OFF		:	6:10 (sunrise)

oPress the HOUR and MIN buttons to set the time.

Example: If you want your lights to turn On at sunset and to turn Off at 10:00 PM, set P1 OFF to 22:00. If you also want your lights to turn back On at 5:00 AM then turn Off at sunrise, set P2 ON to 5:00.

P1 ON	:	20:38 (sunset)
P1 OFF	:	22:00 (programmed)
P2 ON	:	5:00 (programmed)
P2 OFF	:	6:10 (sunrise)

NOTE: P1 OFF and P2 OFF have priority over P1 ON and P2 ON respectively. For example, if sunrise is at 4:58 and P2 ON is set to 5:00, the lights will not turn on.

You can replace the sunrise and sunset times by fixed times. Select program P1 ON or P2 OFF and enter the desired time using the HOUR and MIN buttons.

pPress one of the control buttons or close the switch door to return to normal operation.

Clearing a programmed time

nPress the PGM button to display the programmed time.

oPress the CODE button. The time will be erased and - : - - will be displayed.

NOTE: For P1 ON and P2 OFF, if you have programmed the city parameters, the programmed time will be replaced by sunset time and sunrise time respectively.

pPress one of the control buttons or close the switch door to return to normal operation.

vTroubleshooting

Blank display	• Verify circuit breaker at main panel.
	• Ensure the ON/OFF selector is at ON.
	• Reset the switch using a paper clip.
Faded or irregular	Ambient temperature below freezing point
display
Cannot switch between 24-	First, press one of the control buttons so that
hour format and	MAN or AUTO appears on display.
12-hour format
Programs do not run as	• Make sure the switch is properly programmed.
expected	• Note that - : - - indicates an inactive program,
	00:00 indicates midnight.
	• If the switch has been configured for
	12-hour format, check that PM appears on the left
	side of the screen when an afternoon time is dis-
	played.
The switch resets itself with-	The reset is caused by the load. Install a snubber
out apparent reason when	(AC130-03) at each relay/contactor.
used to control an inductive
load such as a relay or a
contactor.
After I have bypassed the	Any temporary bypass is cancelled at midnight.
program to turn the light Off,	Thus, the light has turned back On, the state the
it turns back On at midnight.	light should be at midnight according to the pro-
	gram. If you often bypass programming before
	midnight, you should program P1 OFF to midnight
	or earlier. This ensures that the light will remain
	Off when you bypass programming.

wTechnical Specifications

Supply: 120 VAC, 50 / 60 Hz

Maximum load: 2400 watts resistive or inductive, 1 HP motor

Operating temperature range: 5°F to 122°F (-15°C to 50°C)

Storage temperature range: -4°F to 122°F (-20°C to 50°C)

Power outage: The programs are protected by a rechargeable battery. The screen is blank during the power outage.

Solar table precision: +/- 11 min. (max error around poles)

Certifications: CSA & UL

TI035 400-035-001-C 13/3/07 2/2