Audiovox AAAAAV-427V-427V-427V-427V-427 CD Changer Controls / Error Code, CD Changer Error Code

CD CHANGER CONTROLS

Built into this radio are controls to operate an optional CD changer. Please check with your Rampage/ Audiovox car stereo specialist for recommendations of the models that will work with this radio.

IMPORTANT: TheCDChangerSelectorSwitchonthe bottom of the chassis must be set to the correct position to match the type of changer being used with this radio. The Re-Set button crshould then be pressed to activate the change of position. If you are not sure of thecorrectswitchpositionforyourmodelofCDchanger, please check with your Rampage/Audiovox retailer or contact us directly at 1-800-645-4994.

NOTE: Switch position for model ACC-30 changer is "B".

Adjustment of the audio functions (volume, tone, balance, and fader) for the CD changer operate in the same manner as they do for radio play. The following controls will operate the CD changer when it is installed and connected to this radio. Refer to the owner’s manual included with the CD changer for instructions on the installation and correct loading and use of the CD magazine.

ct CD CHANGER MODE SELECTOR (CD)

PAUSE/PLAY SELECTOR ( II )

During radio, or tape play, press this button to select operation of the CD changer as shown by “CD-C” and “CdC” on the display panel. Disc play will begin and the disc and track number will be shown on the display panel. If a new magazine has been loaded into the changer, play will begin from the first track of the first disc in the magazine. If a magazine was already in the changer, play will resume from the track on the disc previously in play.

During CD changer play, pressing this button once will return to the radio operation. Pressing again will change to tape play if a tape is loaded in the unit or back to CD changer if no tape is loaded.

cu& dl DISC SELECT (CD+ & CD-)

These buttons are used to select the desired disc for play. To advance to a higher number disc, press the CD+ button cu. To return to a lower number disc,

press the CD- button dl. The number of the disc in play will be shown on the display panel.

dm TRACK SELECT ( / )

This button is used to quickly select the beginning of a particular track. With each momentary press of the Forward Track Select button ( ), the next higher track number will be selected as shown on the display panel. Similarly, with each momentary press of the Backward Track Select button ( ), the next lower track number will be selected. Pressing and holding either button will continue to change tracks in the selected direction.

dn FOWARD SEARCH (SEEK)

High-speed audible search to any forward section of the disc can be made with this feature. Press and hold the button to advance rapidly in the forward direction.

do TRACK REPEAT PLAY SELECTOR (RPT) When the Repeat button is pressed, the “RPT” indication will appear on the display panel and play of the selected track will be continually repeated until the Track Repeat mode is canceled by pressing the Repeat button again or by activating the Random dq or Scan dp functions.

dp TRACK SCAN SELECTOR (SCN)

WhentheScanbuttonispressed,the“SCAN”indication will appear on the display panel, and the first 10 seconds of each track on the disc will be played in order. When a desired track is reached, press the Scan button again and play of the selected track will continue (“SCAN” will disappear from the display panel). The Track Scan mode will also be canceled by activating any other disc function (Track Select, Repeat or Random).

dq RANDOM PLAY SELECTOR (RND)

When the Random button is pressed, the “RND” indication will appear on the display panel and the tracks on the disc will be played in a random, shuffled order. The Track Select buttons dm will also select tracks in the shuffled order instead of the normal progression. The Track Shuffle mode can be canceled by pressing the Shuffle button again or by activating the Repeat door Scan dpfunctions.

CD CHANGER CONTROLS / ERROR CODE

CD CHANGER ERROR CODE

If a problem should develop while operating the CD changer, the error code “Err” may appear on the display panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the microprocessor control of the changer. If the error code should appear, try ejecting and re-loading the magazine into the changer. While the magazine is out of the changer, make sure the discs are clean, undamaged, and loaded correctly (see Owner’s Manual of the CD changer). You may also try activating the Re-Set button cr on the unit, but this will also erase the time and pre-set memories.

If the suggested measures do not solve the problem, contact an approved warranty station near you for further assistance.

10