Avalon Stoves Rainier Floor Protection Requirements

8Stove Installation (for qualified installers only)

Travis Industries 100-01140 4020628

Floor Protection Requirements

•Stove must be placed on the Travis Industries legs or Pedestal.

Minimum

37-3/4"

Minimum 41-3/8"

Min. 16”

Min. 6”

Floor protection must be

non-combustible and at least

.018" thick (26 gauge).

Contents

Main Rainier (945/990) 2Introduction Introduction Important Information Table of Contents General Information Stove Installation Insert Installation Operating Your Appliance 4Safety Precautions Gas Travis Industries 100-01140 4020628 Safety Precautions Mobile Home 6Features & Specifications Installation Options: Features: Heating Specifications: Dimensions: SAFETY NOTICE: Preparation for Installation Stove Installation Considerations Travis Industries 100-01140 4020628 Floor Protection Requirements Stove must be placed on the Travis Industries legs or Pedestal. Stove Placement Requirements Clearances Travis Industries 100-01140 4020628 Chimney Requirements } } } Travis Industries 100-01140 4020628 Chimney Termination Requirements at least 2' above any portion of the roof within 10' Outside Air Requirements Alcove Installation Requirements Rainier-45Rainier-90 Minimum Clearance (See the illustration below) Mobile Home Requirements Minimum Clearance (See the illustration below) Rainier-45 Rainier-90 Travis Industries 100-01140 4020628 Standard Ceiling with a Factory } } Cathedral Ceiling with a Factory } Exterior Factory } } Hearth Stove Positive Hearth Stove Interior or Exterior Masonry SAFETY NOTICE: Preparation for Installation Insert Installation Considerations Surround Panels Insert Size Requirements (see Illustration below) Insert Placement Requirements Minimum Clearances Hearth Requirements Masonry Fireplace Requirements Zero-Clearance (Metal) Fireplace Requirements: Drafting Performance Leveling Bolt Installation Travis Industries 100-01140 4020628 Block-Off Plate Installation Positive (Masonry Fireplace) (Z.C. Fireplace) Face Seal Safety Notice: Before Your First Fire Verify the Installation Curing the Paint 2 to 4 hours Starting a Fire Adjusting the Burn Rate Ash Removal Optional Blower Operation Re-Loading the Stove Overnight Burn Normal Operating Sounds Hints for Burning Selecting Wood Dry Wood is Key Testing Wood Moisture Why Dry Wood is Key Troubleshooting Daily Maintenance (while stove is in use) Remove Ash (if necessary) ASHES Clean the Glass (if necessary) Monthly Maintenance (while appliance is in use) Door and Glass Inspection Creosote - Formation and Need for Removal Yearly Maintenance Door Parts Replacing the Glass Replacing the Door Gasket Replacing the Door Handle Travis Industries 100-01140 4060417 Firebox Parts Floor and Side Firebrick Removal & Replacement Do not pry firebrick - they chip and crack easily. 34 Maintaining Your Appliance Air Tube Removal & Replacement b b a Limited 7 Year Warranty 35 Travis Industries 100-01140 4050124 Years 1 & 2 - COVERAGE: PARTS & LABOR Ceramic Glass Firebrick 36 Listing Label MODEL: SIDEWALL ADJACENT WALL STOVE Stove Leg Installation (Brass # 99200500, Cast Black # 99200800, Sculptured # 99200105) Pedestal (Part # 99200127) Outside Air Installation (for wood stoves only) ! + 1 2 3 4 Rear Blower Installation (Part number 99000138) a c 3 Install the wire clip following the directions below. 4 Attach the blower following the directions below. b Outside Air Boot Installation Travis Industries 100-01140 4051104 Surround Panels (see part #'s below) PANEL SIZING INSTALLATION INSTRUCTIONS Insulation Installation (required for face seal installations only) Front Blower (part # 99000137) TO SWITCH THE POWER CORD TO THE LEFT SIDE: INSTALLATION INSTRUCTIONS Page 44 Index