20 Insert Installation (for qualified installers only)

Block-Off Plate Installation

Whenever this appliance is installed with a direct connection a block-off plate, or other non- combustible seal-off device (e.g. damper adapter), will need to be installed. This device is used to seal the chimney, insuring no smoke enters the home and providing the chimney system with a seal to promote draft. The directions below detail the steps for construction and installation of a block-off plate.

1.Determine a location for the block-off plate at the top of the firebox below the damper area (make it high enough to allow installation of the connection pipe). The location should be level and in an area where it can be mounted easily. Measure the width at the rear ("A") and front ("B") of the firebox at the height where the block-off plate will be installed (see the illustration below). Then measure the depth of the location where the block-off plate will be installed ("C").

NOTE: Most masonry fireplaces have square fireboxes while certain zero-clearance (metal) fireplaces often have domed firebox tops. This makes zero-clearance block-off plates more difficult to install. To simplify the procedure, insulation may be used to seal the rounded edges.

2.Make a cardboard template of the measurements, but add a 2" flange to each side. This flange will be used to mount the block-off plate to the inside of the firebox. Bend the flanges downwards on the template and place it inside the fireplace. If the template fits correctly in its planned location, go to the next step. If it does not, make a new template with the appropriate corrections until it fits correctly.

3.With the template in place, mark the location of the flue (see “Dimensions” on page 6). This location approximates the center of the flue when the insert is in place (a slight offset may occur based upon insert and block-off plate placement). Remove the template and cut a 6 1/4" diameter hole centered on this mark.

4.Make the block-off plate of 24 gage or thicker steel to match the template. Drill two holes in each flange for mounting the plate.

5.Mount the block-off plate using masonry screws.

NOTE: Use sheet metal screws on zero-clearance (metal) fireplaces (screws need only be long enough to penetrate the first layer of metal).

6.Insulate the block-off plate using high-temperature fiberglass insulation (Kaowool® or equivalent) and furnace cement (allow the cement to dry for at least 24 hours before burning).

7.After placing the appliance and installing the pipe through the block-off plate, use high- temperature fiberglass insulation and furnace cement to seal any cracks between the pipe and block-off plate.

See the

dimensions to

determine the

location of the

center of the

flue.

 

Damper

B

 

C

A

Firebox

Block-Off Plate Template

2" Flanges

Measurement

(for attaching

"A"

the block-off

 

plate)

 

Measurement

"C"

Measurement "B"

See the dimensions to determine the location of the center of the flue.

Travis Industries

100-01140

4 020628

Page 20
Image 20
Avalon Stoves Rainier owner manual Block-Off Plate Installation, Block-Off Plate Template

Rainier specifications

Avalon Stoves has long been synonymous with quality and innovation in the fireplace and heating industry. Among its distinguished lineup is the Avalon Rainier, a stove that embodies both modern aesthetics and cutting-edge heating technology. Designed for those who appreciate the warmth of a fire while also seeking efficient heating solutions, the Rainier stands as a testament to Avalon’s commitment to excellence.

One of the standout features of the Avalon Rainier is its impressive heating capacity. With the ability to heat spaces up to 2,000 square feet, this stove is perfect for larger homes or open-concept living areas. The Rainier boasts a powerful EPA-certified firebox, which enhances its efficiency and reduces emissions, ensuring that you not only enjoy the ambiance of a fire but also adhere to modern environmental standards.

The stove's advanced combustion technology is another remarkable characteristic. The Rainier employs a secondary combustion system, allowing for a cleaner burn and maximized heat output. This system significantly reduces the amount of smoke produced, providing a more pleasant experience while increasing the lifespan of the stove. The result is a cleaner environment and extended fuel efficiency.

In terms of design, the Avalon Rainier does not disappoint. It features a contemporary aesthetic that can seamlessly integrate into any home decor. With various finishes and optional tile surrounds, personalization is easy, allowing homeowners to dial up their unique style. The large viewing window enhances the visual appeal of the fire, inviting the warm glow into any room.

User-friendly functionalities set the Rainier apart from its competitors. The stove includes an intuitive air control system that allows for precise adjustments of the heat and burn rate. Additionally, the optional blower system enhances air distribution, ensuring that even the far corners of your home receive optimal warmth.

Durability is paramount in the construction of the Avalon Rainier. Made from high-quality materials, including heavy-duty steel and cast iron, the stove is built to withstand the rigors of daily use while maintaining its elegant look.

In summary, the Avalon Stoves Rainier offers an impressive combination of heating efficiency, desirable aesthetics, and user-friendly features. Whether you are looking to reduce your heating costs or simply enjoy the cozy atmosphere of a wood-burning fire, the Rainier is an excellent choice that exceeds expectations. Its commitment to both performance and design makes it a standout option for any homeowner.