Manuals / Brands / Home Audio / Home Theater System / Barco / Home Audio / Home Theater System

Barco R9010040, R9010050 How to adjust Peaking?, 8.5.7 Line Multiplier Settings, 8.5.7.1 Starting up Line Multiplier settings

1 115

Download 115 pages, 3.63 Mb

8. Random Access Adjustment Mode

How to adjust Peaking?

1. Push the cursor key ↑or ↓to highlight Peaking and press ENTER. (menu 8-15)

Note: During the creation of new settings for a RGB source the corresponding peaking is switched on as default.

The Peaking menu will be displayed. (menu 8-16)

The following frequency areas are available:

Low Frequency Peaking 15–45Hz

Mid Frequency Peaking 45–85Hz

High Frequency Peaking 85–110Hz

2. Push the cursor key ↑or ↓to select the desired frequency area or off and press ENTER to activate.

3. Press EXIT to return to the Picture Tuning menu.

PICTURE TUNING

COLOR BALANCE

SYNC: FAST

DECODING : EBU

PORT2 : VIDEO

PEAKING

LINE MULTIPLIER : ON

Select with ↑or ↓

then <ENTER>

<EXIT> to return

Menu 8-15

PEAKING

OFF

LOW FREQUENCY

MID FREQUENCY

HIGH FREQUENCY

Select with ↑or ↓

then <ENTER>

<EXIT> to return

Menu 8-16

8.5.7 Line Multiplier Settings

Overview

• Starting up Line Multiplier settings

• Switching the multiplier ON/OFF

• Motion Processing On/Off

• Output Mode

• Video Equalizing

• Noise Reduction

• Contrast Enhancement

• Split Screen On/Off

• Advanced Settings

8.5.7.1 Starting up Line Multiplier settings

What can be done?

The multiplier eliminates the video line patterns and improves the image stability.

In addition:

• The time base correction virtually eliminates the timing jitter caused by the common videocassette recorders.

• De-interlacing gets rid of line flicker.

• Film mode processing makes sure that material that has been converted from 24 Hz cinema to video (2:2 and 3:2 pull down) is

displayed without artifacts.

• Dynamic noise reduction can be used to improve noisy video sources.

• Static contrast enhancement allows the user to adjust the image contrast to personal taste.

• Several detail-enhancing filters bring out details.

Line multiplying is only possible for Video, S-Video, Component Video images on standard line frequency and

RGB signals on 15 kHz.

The setting of the line multiplier will be saved together with the source number. Each time this source number

is selected, the last saved version will be loaded.

R5976584 BARCO CINE7 26022003 57

Contents

Main BARCO CINE7 Page Page Page Table of contents TABLE OF CONTENTS Table of contents Page Page 1. SAFETY INSTRUCTIONS 1.1 Safety Instructions 1. Safety Instructions On Safety Caution on Fire Hazard 1. Safety Instructions On Installation On Servicing On Cleaning On Repacking On Illumination Page 2. AC POWER 2.1 AC Power Cord Connection 2.2 AC Power Voltage 2.3 Switching ON/OFF Page 3. SOURCE CONNECTIONS 3.1 Input Locations Input Facilities Which source to which input 3.2 Connecting a Composite Video source. 3.3 Connecting a S-Video source. Input priority setting Menu 3-1 Menu 3-3 Menu 3-5 Menu 3-2 3.4 Connecting a RGB Analog source with composite sync Which signals can be connected to the input R5976584 BARCO CINE7 26022003 15 Image 3-6 RGBS or RGsB selection via the RCU 3.5 Connecting a RGB Analog source with Tri level composite sync 3.6 Connecting a Component source with composite sync 3.7 Connecting a Component source with Tri level composite sync 3.8 RS232 Connection 3.9 Communication Port for Communication With Peripherals 3.10 12V Trigger output 4. GETTING STARTED 4.1 Batteries 4.2 RCU & Local keypad Remote control functions. 4.3 Terminology overview Page 4.4 Switching on the projector Howtoswitchontheprojector? The switching on modes Starting up in Operational Mode How to interrupt the warm up period? 4.5 Using the RCU 4.6 Projector Address 4.7 Controlling the projector Overview Picture controls Overview Sound Controls The Pause Key Page 5. Start up of the adjustment mode 5. START UP OF THE ADJUSTMENT MODE 5.1 How to start up the adjustment mode Start up using the RCU Start up using the local keypad Possible paths Page 6. MAIN MENU 6.1 Main Menu Overview Main Menu Overview 6.2 Image Control 6.2.1 Starting up the image controls To start up 6.2.2 Line Multiplier 6.2.2.1 Changing the Multiplier setting Why line multiplying How to change the Multiplier setting Line Multiplier ON/OFF 6.2.2.2 Multiplier mode What can be selected? Start up the Multiplier mode Changing the scan rate 6.2.2.3 Motion Processing On/Off How to toggle Motion Processing On/Off? 6.2.2.4 Video Equalizing How to adjust Video Equalizing? 6.2.2.5 Noise Reduction How to adjust Noise Reduction? Page How to change the color temperature 6.2.4 Format Select 6.2.4.1 Selecting a Format What can be done How selecting a Format. 6.2.4.2 Adding a name to a Format 6.3 IRIS Control What is possible? 6.3.1 Starting up the IRIS Controls How to start up 6.3.2 IRIS Touch Up Start up the IRIS touch up 6.3.3 IRIS Auto Converge 6.4 Sound Control Selecting the sound control. 6.5 Function Keys To get an overview of the programmed keys 6.6 Service Menus How to enter the Service Menus 44 R5976584 BARCO CINE7 26022003 Menu 6-32 Menu 6-31 Menu 6-33 7. ENTERING THE SERVICE MENUS 7.1 The Adjustment menus What is available in the Adjustment menus How to enter the Adjustment menus with the RCU? How to enter the Adjustment menus with the local keypad? 7.2 Password Protection Password Protection Entering the Password via the RCU Entering the Password via the local keypad Page 8. RANDOM ACCESS ADJUSTMENT MODE 8.1 Introduction How to start up Random Access Adjustment Mode? 8.2 Random Access Overview Random Access Overview 8.3 Selecting Setup Pattern HowtoselecttheSetupPattern? When using the Internal # Pattern? Available Factory Preset Frequencies How to select the desired Cross Hatch Frequency? 8.4 Random Access mode selection menu Possibilities 8.5 Picture Tuning 8.5.1 Starting up Picture Tuning How to start up Picture Tuning? 8.5.2 Color Balance 8.5.2.1 Selecting the Color Balance How to select Color Balance 8.5.2.2 Set a Fixed Color Balance 8.5.2.3 Custom Color Balance, White Balance adjustment How to adjust 8.5.2.4 Custom Color Balance, Black Balance adjustment How to adjust 8.5.3 Sync mode: Fast/Slow How to adjust the Sync mode? 8.5.4 Decoding How to set up ? 8.5.5 Port 2 Video/S-Video (Optional) How to configure Port 2? 8.5.6 Peaking How to adjust Peaking? 8.5.7 Line Multiplier Settings 8.5.7.1 Starting up Line Multiplier settings How to start up the Line Multiplier settings? 58 R5976584 BARCO CINE7 26022003 Menu 8-17 Menu 8-18 8.5.7.2 Switching the multiplier ON/OFF How to switch 8.5.7.4 Output Mode How to adjust the Output Mode? 8.5.7.5 Video Equalizing How to adjust Video Equalizing? Page How to adjust the Contrast Enhancement? 8.5.7.8 Split Screen On/Off How to toggle Split Screen On/Off? 8.5.7.9 Advanced Settings 8.5.7.9.1 Starting Up Advanced Settings How to start up Advanced Settings? 62 R5976584 BARCO CINE7 26022003 Menu 8-29 Menu 8-30 8.5.7.9.2 Time Base Correction How to adjust Luminance Delay? 8.5.7.9.4 Vertical Sync Reference How to toggle Vertical Sync Reference Direct/Indirect? 8.5.7.9.5 Clamp Gating When is it necessary? How to toggle Clamp Gating On/Off? 8.5.7.10 Limo Pro Options 8.5.7.10.6 Starting Up Limo Pro Options When available? How to start up Limo Pro Options? 8.5.7.10.7 Coring How to adjust Coring? 8.5.7.10.8 LTI How to adjust LTI? 8.5.7.10.9 CTI How to adjust CTI? 8.5.7.10.10Factory Presets How to set to the Factory Presets? 8.6 Geometry Adjustments 8.6.1 StartingUpGeometry How to start up Geometry? 8.6.2 Horizontal Phase Adjustment How to adjust the Horizontal Phase? 8.6.3 Raster Shift Adjustment What has to be done? How to adjust the Raster Shift? 8.6.4 Left-Right (East-West) Adjustment What can be adjusted ? Possible adjustments Page How to adjust the Seagull correction 8.6.5 Top-Bottom (Nord-South) Adjustment What can be adjusted ? Page Page Page How to adjust the Size? 8.6.7Vertical Linearity Adjustment 8.6.8 Blanking Adjustments How to adjust the Blanking? 8.7 Convergence Adjustment 8.7.1 Starting Up Convergence What has to be done? Adjustment order How to start up Convergence? 8.7.2 Convergence Adjustment Adjustment Order How to perform a Convergence Adjustment? Page 9. SERVICE MODE 9.1 Introduction How to start up Service Mode? 9.2 Service Mode Overview Service Mode Overview 9.3 Projector Set up 9.3.1 Starting Up Projector Set-Up 9.3.2 Identification How to start up Identification? 9.3.3 Total Run Time How to start up Total Run Time? 9.3.4 Change Password How to Change the Password? 9.3.5 Change Language 9.3.6 Change Projector Address How to Change the Projector Address? 9.3.7 Change Baudrate How to Change the Baudrate? 9.3.8 Power Up Mode Operating/Stand-By How to toggle Power Up Mode Operating/Stand By? 9.3.9 Common Address Why 2 different Common Addresses? Page How to add the Barco Logo 9.4 Memory Management 9.4.1 Starting Up Memory Management How to start up the Memory Management? 9.4.2 Copy a Block HowtoCopyaBlock? 9.4.3 Delete a Block How to Delete a Block? 9.4.4 Delete All Blocks How to Delete All Blocks? 9.4.5 All Settings to Midposition How to set All settings to Midposition? How to Undo All settings to Midposition? 9.4.6 R & B Convergence to Midposition How to set R & B Convergence to Midposition? How to Undo Convergence R & B to Midposition? 9.4.7 Green Convergence to Midposition How to set Green Convergence to Midposition? How to Undo Green Convergence to Midposition? 9.5 Common Settings 9.5.1 Starting Up Common Settings How to start up Common Settings? 9.5.2 G2 Adjustment How to start up G2 adjustment? 9.5.3 CRT Run In Cycle When necessary? What is done? How to select CRT Run In Cycle? 9.5.4 Projector Warm Up 9.5.5 Memory Banks Howtocreateanewmemor 9.6 I2C Diagnostics Page 10. Programmable Function Keys 10. PROGRAMMABLE FUNCTION KEYS 10.1 Programming a Function Keys What can be done with these keys? How can a Function key be programmed? Example programming horizontal phase on key F4 10.2 Different function which can be programmed. Factory predefined functions 11. Messages, Warnings and Failures 11. MESSAGES, WARNINGS AND FAILURES 11.1 Messages Messages 11.2 Warnings Warnings 11.3 Failures A. Source Numbers 81 86 and 91 96 A. SOURCE NUMBERS 81 86 AND 91 96 A.1 Projector without any 800 peripheral connected How to create a second source? A.2 Projector with a 800 peripheral connected A.2.1 Source numbers 91 96 A. Source Numbers 81 86 and 91 96 A.2.2 Source numbers 81 86 Glossary GLOSSARY Page INDEX A B C D L M N O P T V W Page Revision Sheet