Connect
1 | CHIL | +12V | 1 | CHIL |
MIN | FUSE 30A X 4 |
| MIN | FUSE 30A X 4 |
MASTER | + |
| SLAVE |
|
| AMPLIFIER | |
AMPLIFIER |
| *4 Ohm | |
|
| ||
|
| 2 Ohm Minimum |
|
+12V | ENGLISH |
|
CAUTION! In bridged operation, the amplifiers must see a 2 Ohm load or higher for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifiers to overheat and possibly cause permanent damage to the amplifiers.
When running multiple sets of bridged amplifier’s in large systems all amplifiers can be linked together so the primary master amplifier can control all amplifiers in the set. In the following example we show two sets of bridged amplifiers controlled by one master ampilifer.
Master amplifier’s crossover, bass boost and subsonic adjustments control
both the master and slave amplifiers.
MASTER AMPLIFIER
L R
1.) Set Phase to IN
2.) Set Source to NORMAL
SLAVE AMPLIFIER
1.) Set Phase to OUT
2.) Set Source to SLAVE
SLAVE AMPLIFIER
1.) Set Phase to IN
2.) Set Source to SLAVE
SLAVE AMPLIFIER
1.) Set Phase to OUT
2.) Set Source to SLAVE
SUBSONIC | REMOTE | PHASE | XOVER | SOURCE | SLAVE IN | INPU |
FREQ Hz |
|
| FREQ Hz |
| ||
10 |
| IN | 30 |
| PWR \ |
|
|
| NORMAL |
| |||
80 |
| OUT | 250 | SLAVE | PROT | L |
BASS |
|
|
| + - + - |
| |
BOOST |
|
|
|
|
|
|
30 | 0 |
|
|
|
|
|
125 | dB |
|
|
|
| R |
15 |
|
|
|
| ||
FREQ Hz | BASS BOOST | GAIN |
| SLAVE OUT |
| |
SUBSONIC | REMOTE | PHASE | XOVER | SOURCE | SLAVE IN | INPUT |
FREQ Hz |
|
| FREQ Hz |
| ||
10 |
| IN | 30 |
| PWR \ |
|
|
| NORMAL |
| |||
80 |
| OUT | 250 | SLAVE | PROT | L |
BASS |
|
|
| + - + - |
| |
BOOST |
|
|
|
|
|
|
30 | 0 |
|
|
|
|
|
125 | dB |
|
|
|
| R |
15 |
|
|
|
| ||
FREQ Hz | BASS BOOST | GAIN |
| SLAVE OUT |
| |
SUBSONIC | REMOTE | PHASE | XOVER | SOURCE | SLAVE IN | INPUT |
FREQ Hz |
|
| FREQ Hz |
| ||
10 |
| IN | 30 |
| PWR \ |
|
|
| NORMAL |
| |||
80 |
| OUT | 250 | SLAVE | PROT | L |
BASS |
|
|
| + - + - |
| |
BOOST |
|
|
|
|
|
|
30 | 0 |
|
|
|
|
|
125 | dB |
|
|
|
| R |
15 |
|
|
|
| ||
FREQ Hz | BASS BOOST | GAIN |
| SLAVE OUT |
| |
SUBSONIC | REMOTE | PHASE | XOVER | SOURCE | SLAVE IN | INPUT |
FREQ Hz |
|
| FREQ Hz |
| ||
10 |
| IN | 30 |
| PWR \ |
|
|
| NORMAL |
| |||
80 |
| OUT | 250 | SLAVE | PROT | L |
BASS |
|
|
| + - + - |
| |
BOOST |
|
|
|
|
|
|
30 | 0 |
|
|
|
|
|
125 | dB |
|
|
|
| R |
15 |
|
|
|
| ||
FREQ Hz | BASS BOOST | GAIN |
| SLAVE OUT |
| |
*4 Ohm load recommended for best efficiency
and to optimize the power output.
1 
MIN
1 
MIN
1 
MIN
1 
MIN
CHIL
CHIL
CHIL
CHIL
FUSE 30A X 4
FUSE 30A X 4
FUSE 30A X 4
FUSE 30A X 4
+12V
+
+12V
*4 Ohm
2
Ohm
Minimum
+12V | GND | |
+ |
|
|
+12V | GND |
*
4 Ohm
2 Ohm Minimum
14 | MGA AMPLIFIERS |
