Beko CDA543F Electrical Requirements, Transportation Instructions, Installation Instructions

ELECTRICAL REQUIREMENTS

Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating plate inside the appliance corresponds to your electricity supply.

Rating label is on the left hand side of fridge inner liner.

We recommend that this appliance is connected to the mains supply via a suitable switched and fused socket in a readily accessible position.

Should the mains lead of the appliance become damaged or should it need replacing at any time, it must be replaced by a special purpose made mains lead which can only be obtained from a BEKO Authorised Service Agent.

WARNING! THIS APPLIANCE MUST BE EARTHED

If the fitted moulded plug is not suitable for your socket, then the plug should be cut off and an appropriate plug fitted. Destroy the old plug which is cut off as a plug with bared cord could cause a shock hazard if inserted into a socket elsewhere in the house.

The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse need to be replaced an ASTA approved BS 1362 fuse of the same rating must be used. Do not forget to refit the fuse cover. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted. Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug. Fuse covers are available from any good electrical store.

TRANSPORTATION INSTRUCTIONS

1.The appliance should be transported only in a vertical upright position. The packing as supplied must be intact during transportation.

2.If during the course of transport the appliance has to be transported horizontally, it must only be laid on its right hand side when standing in the front of the appliance. After bringing it to upright position,it must not be operated for at least 4 hours to allow the system to settle.

3.Failure to comply with the above instructions could result in damage occuring to the appliance. The manufacturer will not be held responsible if these instructions are disregarded.

4.The appliance must be protected against rain, moisture and other atmospheric influences.

5.When positioning your appliance take care not to damage your flooring, pipes, wall coverings etc. Do not move the appliance by pulling by the door or handle.

6.Empty any water in the drain tray before moving. See section ‘Defrosting’ and ‘Care & cleaning’ for further information.

7.Make sure that the defrost water pipe at the back of the product is fixed to the plastic evaporating pan on the top of the compressor, to avoid defrost water

spillage on the floor.

IMPORTANT : Care must be taken while cleaning / carrying the appliance to avoid touching the bottom of the condenser metal wires at the back of the

IMPORTANT! FITTING A DIFFERENT PLUG As the colours of the wires in the

mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

(See diagram).

1.Connect the green-yellow or green (Earth) wire to the terminal in the plug marked 'E' or with

the symbol or coloured green and yellow or green.

2.Connect the blue (Neutral) wire to the terminal in the plug marked 'N' or coloured black.

GREEN &
					6mm.
YELLOW
OR	32mm.				L .
GREEN
				BROWN			6mm
N					OR
			22mm. RED
BLUE						12mm.
OR		.6mm
BLACK

CORD GRIP

	FITTED WITH BS 1362 13A FUSE ALWAYS FIT BS 1362 REPLACEMENT CARTRIDGE FUSE
FUSE

appliance as you might injure your fingers and hands.

Do not attempt to sit or stand on top of your appliance as it is not designed for such use. You could injure yourself or damage the appliance.

"IMPORTANT: Make sure that mains cable is not caught under the appliance during and after carrying / moving the appliance, to avoid the mains cable becoming cut or damaged."

Do not allow children to play with the appliance or tamper with the controls. BEKO plc declines to accept any liability should the instructions not be followed.

IMPORTANT

INSTALLATION INSTRUCTIONS

1. The space in the room where the appliance is installed must not be smaller

than 10 cubic metres.

2. Do not put your fridge freezer in a cold room where the temperature is likely

to go below +5 degrees C (41 degrees F) during night time and/or especially

in winter.

3.Connect the brown (Live) wire to

the terminal in the plug marked 'L' or coloured red.

With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or in the main fuse box.

If in doubt contact a qualified electrician.

3

This fridge freezer has been designed to operate in ambient temperatures

between +5 and +32 degrees C (41 and 90 degrees F) Therefore if the

appliance is installed in an unheated/cold room (eg: conservatory/annex/

shed/garage etc) then the appliance will not operate causing the freezer

compartment to run warmer and as a result the storage time of frozen food
may be reduced.	4