Transport instructions, Disposal, Device setup

Transport instructions

The device should be transported only in upright position.

The packing as supplied must be intact during transportation.

After a transport in the horizontal position, the device may only be taken into operation 4 hours after being stood up vertically again. The appliance must be protected against rain, moisture and other atmospheric influences. The manufacturer assumes no liability if safety instructions are disregarded.

Disposal

Make the device unusable immediately. Pull out the mains plug and cut the power cable. Remove or destroy snap or latch locks before disposing of the device. In this manner you prevent children from locking themselves in and endangering their lives.

Device setup

•Do not operate your appliance in a room where the temperature is likely to fall below 10 °C at night and/or especially in winter. At lower temperatures the appliance may not operate, resulting in a reduction in the storage life of the food.

•The climate class rate of your appliance is given in Technical Features leaflet and written on the rating label inside the appliance. It specifies the appropriate operating ambient temperatures as explained below.

Climatic class	Ambient temperatures
SN	+10 °C to 32 °C
N	+16 °C to 32 °C
ST	+18 °C to 38 °C
T	+18 °C to 43 °C
SN-ST	+10 °C to 38 °C
SN-T	+10 °C to 43 °C

Location

Only place the device in dry rooms which can be aired.

Avoid direct sunlight or direct heat sources such as a stove or a heater.

If this cannot be avoided, the following minimum distances should be maintained: Electric stoves: 3,00 cm

Heater: 3,00 cm

Cooling devices: 2,50 cm

•Ensure sufficient air circulation for your device.

•Make sure that sufficient room is provided around the appliance to ensure free air circulation.

Fit the two plastic wall spacers supplied with the appliance rotating 1/4 turn to the condenser at the back of the appliance (Fig. 3).

•The device should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that your appliance is standing upright adjust the two front feet by turning clockwise or counter-clockwise, until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise.

Electrical connections

Warning

This device must be grounded.

•Check whether the power type and voltage in the device location corresponds to the one stated on the rating label inside the device.

•The electrical safety of the device is only assured when the grounding system in the house is installed in accordance with regulations.

•When putting the device in, do not stand it on the power cable, otherwise the cable will be damaged.

•Ensure that the plug remains readily accessible. Do not use multiple adapter bar or extension cable.

D 8451 SM, D 8450 SM, D1 8450 SM, D1 8451 SM specifications

The Beko D1 8451 SM, D1 8450 SM, D 8450 SM, and D 8451 SM are advanced models in the Beko washing machine lineup, each designed to cater to different consumer needs while ensuring exceptional performance and energy efficiency. These machines reflect Beko’s commitment to innovation and quality in home appliances.

One of the standout features of the Beko D1 8451 SM and D1 8450 SM models is their ProSmart Inverter Motor, which operates quietly and is designed for longevity. This technology reduces energy consumption and vibration, making the washing process much more efficient and pleasant. Additionally, the inverter motor ensures that each cycle is tailored to meet the demands of the load, providing a gentle yet effective cleaning performance.

The D 8450 SM and D 8451 SM models incorporate Beko's AquaTech technology, allowing for quicker wash times without compromising on cleanliness. This feature uses a unique water dispersal system that ensures water penetrates fabrics more efficiently, thus providing a thorough wash in less time. Perfect for households with busy schedules, this technology saves time and energy.

All four models are equipped with an EcoSmart feature that optimizes energy and water usage based on the selected washing program and load size. This not only minimizes utility bills but also reduces the environmental impact of laundry, aligning with increasingly eco-conscious consumer preferences.

The user interface on the Beko D1 8451 SM and D1 8450 SM is designed for ease of use, featuring a clear digital display that allows users to easily select their preferred washing programs. These models come with an array of programs tailored for different fabrics and levels of soiling, ensuring that users can select the perfect cycle for every load.

Additionally, all variants boast a sleek and modern design, making them an attractive addition to any laundry room. With a range of capacity options, they cater to both small households and larger families. Their robust build quality ensures durability and performance longevity, making them a reliable choice for consumers.

In conclusion, whether you opt for the Beko D1 8451 SM, D1 8450 SM, D 8450 SM, or D 8451 SM, you can expect a high level of efficiency, advanced technology, and user-friendly features that enhance the overall laundry experience. Each model is designed to meet the diverse needs of consumers, bringing convenience, performance, and sustainability into the home.

Beko D 8450 SM Transport instructions, Disposal, Device setup, Location, Electrical connections

Models: D 8451 SM D 8450 SM D1 8450 SM D1 8451 SM