Beko HBG70X Installation Instructions, Applicable for external air evacuation, Insulation class

applicable for external air evacuation.

Before connecting the model to the electricity network:

-control the data plate (positioned inside the appliance) to ascertain that the voltage and power correspond to the network and the socket is suitable. If in doubt ask a qualified electrician.

-If the power supply cable is damaged, it must be replaced with another cable or a special assembly, which may be obtained direct from the manufacturer or from the Technical Assistance Centre.

-This device must be connected to the mains supply through either a plug fused 3A or hardwired to a 2 phase spur pro- tected by 3A fuse.

2. Warning!

In certain circumstances electrical appliances may be a danger hazard.

A)Do not check the status of the filters while the cooker hood is operating.

B)Do not touch bulbs or adjacent areas, during or straight after prolonged use of the lighting installation.

C)Flambè cooking is prohibited underneath the cooker hood.

D)Avoid free flame, as it is damaging for the filters and a fire hazard.

E)Constantly check food frying to avoid that the overheated oil may become a fire hazard.

F)Disconnect the electrical plug prior to any maintenance.

G)This appliance is not intended for use by young children or infirm persons without supervision.

H)Young children should be supervised to ensure they do not play with the appliance.

I)There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances burning gas or other fuels.

L)There is a risk of fire if cleaning is not carried out in accordance with the instructions.

This appliance conforms to the European Directive EC/2002/96, Waste Electrical and Electronic Equipment (WEEE). By making sure that this appliance is disposed of in a suitable manner, the user is helping to prevent potential damage to the environment or to public health.

The symbol on the product or on the accompanying paperwork indicates that the appliance should not be treated as domestic waste, but should be delivered to a suitable electric and electronic appliance recycling collection point. Follow local guidelines when disposing of waste. For more information on the treatment, re-use and recycling of this product, please contact your local authority, domestic waste collection service or the shop where the appliance was purchased.

INSTALLATION INSTRUCTIONS

•Assembly and electrical connections must be carried out by specialised personnel.

•Wear protective gloves before proceeding with the installation.

•Electric Connection

Note: Verify the data label placed inside the appliance:

-If the symbol appears on the plate, it means that no earth connection must be made on the appliance, therefore follow the instructions concerning insulation class II.

-If the symbol DOES NOT appear on the plate, follow the instructions concerning insulation class I.

Insulation class II

The appliance has been manufactured as a class II, therefore no earth cable is necessary.

The plug must be easily accessible after the installation of the appliance. If the appliance is equipped with power cord without plug, a suitably dimensioned omnipolar switch with 3 mm minimum opening between contacts must be fitted between the appliance and the electricity supply in compliance with the load and current regulations.

The connection to the mains is carried out as follows: BROWN = L live wire

BLUE = N neutral

Insulation class I

This is a class I, appliance and must therefore be connected to an effiecient earthing system.

The appliance must be connected to the electricity supply as follows:

BROWN = L live wire BLUE = N neutral YELLOW/GREEN = earth

The neutral wire must be connected to the terminal with the N symbol while the YELLOW/GREEN, wire must be connected to the terminal by the earth symbol .

Warning:

When connecting the appliance to the electricity supply, make sure that the mains socket has an earth connection. After fitting the ducted cooker hood, make sure that the electrical plug is in a position where it can be accessed easily. If the appliance is connected directly to the electricity supply, an omnipolar switch with a minimum contact opening of 3 mm must be placed in between the two; its size must be suitable for the load required and it must comply with current legislation.

•The minimum distance between the support surfaces of the cooking pots on the cooker top and the lowest part of the cooker hood must be at least 65 cm. If a connection tube composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or for evacuating fumes from other appliances generated by other than an electrical source.

Before proceeding with the assembly operations, remove the anti-grease filter(s) (Fig.7) so that the unit is easier to handle. In the case of assembly of the appliance in the suction version prepare the hole for evacuation of the air.

•We recommend the use of an air exhaust pipe with a diameter of 150. If a pipe with a smaller diameter is used, the efficiency of the product may be reduced and its operation may become noisier.

Please note:

If your version of the appliance has decorative glass before installing the hood, carry out the following steps as shown in figure 4:

1 - Remove both the cooker hood body B and the glass panel A from the packaging and place them horizontally on a secure surface.

2 - Take the glass panel A and position it above the cooker hood body B.

3 - Fix the glass panel securely to the cooker hood body using

- 16 -