H001_En

POWER-CORD PROTECTION — Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

OUTDOOR ANTENNA GROUNDING — If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

LIGHTNING — For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

POWER LINES — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

OVERLOADING — Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

OBJECT AND LIQUID ENTRY — Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

SERVICING — Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

DAMAGE REQUIRING SERVICE — Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

•When the power-supply cord or plug is damaged.

•If liquid has been spilled, or objects have fallen into the product.

•If the product has been exposed to rain or water.

•If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

•If the product has been dropped or damaged in any way.

•When the product exhibits a distinct change in performance — this indicates a need for service.

REPLACEMENT PARTS — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

SAFETY CHECK — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

WALL OR CEILING MOUNTING — The product should not be mounted to a wall or ceiling.

HEAT — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

ANTENNA

LEAD IN WIRE

GROUND

ANTENNA

CLAMP

DISCHARGE UNIT

 

 

(NEC SECTION 810-20)

ELECTRIC

GROUNDING CONDUCTORS

SERVICE

(NEC SECTION 810-21)

EQUIPMENT

GROUND CLAMPS

 

 

POWER SERVICE GROUNDING

 

ELECTRODE SYSTEM

Fig. A

(NEC ART 250, PART H)

 

NEC — NATIONAL ELECTRICAL CODE

WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

[For U.S. model]

IMPORTANT NOTICE

The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. H006A_En

4

Page 4 Page 6
Page 5
Image 5
Bel Canto Design PL-1A manual For U.S. model, Important Notice
Page 4 Page 6

PL-1, PL-1A specifications

Bel Canto Design has long been synonymous with high-performance audio equipment, and its PL-1A and PL-1 models are no exception. These preamplifiers stand out in the world of high-fidelity audio for their refined technology, elegant design, and exceptional sound quality.

The Bel Canto PL-1A is a state-of-the-art digital preamplifier that caters to audiophiles demanding precision and versatility. It features a fully balanced signal path, which helps to minimize noise and distortion, ensuring that the music signal remains pure and unaltered. The PL-1A employs advanced digital signal processing technology, which not only enhances the audio performance but also provides a range of connectivity options to accommodate various audio sources.

One of the standout features of the PL-1A is its high-resolution asynchronous USB input, allowing users to connect their computers or digital audio players seamlessly. This input supports high sample rates, making it ideal for high-definition audio formats. Additionally, it includes multiple digital inputs such as coaxial and optical, along with analog inputs, providing flexibility for integrating different audio components.

The PL-1A also comes with an intuitive user interface, making it easy to navigate through the various settings and options. The remote control allows users to adjust volume levels, select inputs, and control other features without the need to get up from their listening position, enhancing the overall convenience.

The design of the PL-1A is not just functionally excellent but also visually appealing. Its sleek chassis is made of high-quality materials, giving it a premium look and feel that complements any audio setup. The attention to detail in both the design and craftsmanship ensures that it not only performs exceptionally well but also stands the test of time.

On the other hand, the Bel Canto PL-1 serves as a more traditional analog preamplifier, offering a warm, rich sound that many audiophiles crave. It features a robust power supply, low-noise circuits, and high-quality components that contribute to its stellar audio performance. The PL-1 is designed for both vinyl enthusiasts and digital audio lovers, providing inputs for turntables as well as digital sources.

Both models embody Bel Canto Design’s commitment to quality, innovation, and state-of-the-art audio technologies, making them ideal choices for anyone looking to elevate their listening experience. With their advanced features, aesthetic appeal, and superior sound quality, the Bel Canto PL-1A and PL-1 preamplifiers promise to satisfy even the most discerning audiophiles.
Top Page Image Contents