Manuals / BenQ / Computer Equipment / Projector

BenQ MP576, MP575, MP525P, MP526 user manual Operation, Reset All Settings

Models: MP526 MP525 MP525P MP575 MP576

1 68

Page 48

Main menu	Sub-menu		Options
		Closed Caption	On/Off
	Closed Caption	Enable	On/Off
	Closed Caption	Enable
		Caption Version	CC1/CC2/CC3/CC4
5.		Control By	RS232/RJ45
5.		DHCP	On/Off
SYSTEM
SYSTEM		Projector IP
SETUP:	Lan Control	Address
Advanced	Settings	Subnet Mask
		Default Gateway
		DNS Server
		Apply
	Reset All Settings
	FAQ-Image and Installation
	FAQ-Features and Service
6.			•	Source
INFORMA-			•	Picture Mode
TION	Current System Status		•	Resolution
TION	Current System Status		•	Color System
			•	Color System
			•	Equivalent Lamp Hour
			•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

48 Operation

Page 48

Image 48

BenQ MP576, MP575, MP525P, MP526 user manual Operation, Reset All Settings

Contents

MP515/MP525/MP525P MP526/MP575/MP576 Digital Projector User Manual WelcomeTable of contents Important safetyPositioning your Warranty and CopyrightImportant safety instructions Safety Instructions3. Refer servicing to qualified service personnel Safety Instructions Continued 4 Important safety instructions14. Do not block the ventilation holes installation Projector features IntroductionShipping contents Standard accessoriesOptional accessories Projector exterior view Front/upper sideRear/lower side Controls and functions Projector5. II Power 9. LAMP indicator light13. Mode/Enter 14. SOURCECeiling mounting the projector Remote control 1. II Power6. Volume + 2. FreezeRemote control effective range Replacing the remote control battery13. Timer On 14. Timer Set upPositioning your projector Choosing a location1. Front Table 2. Front CeilingObtaining a preferred projected image size How to determine the recommended screen size for a given distance 16 Positioning your projectorProjection dimensions Maximum zoomMinimum zoom Screen Center of lens Projection distanceConnection S-Video cableVGA to DVI-A cable Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting audioConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystoneUsing the remote control Using the OSD menuUsing the menus Using a security cable lock Utilizing the password functionSecuring the projector Setting a passwordIf you forget the password Entering the password recall procedureChanging the password 2. Press Mode/Enter. The message INPUT CURRENT PASSWORD is displayedDisabling the password function Switching input signal Magnifying and searching for details Selecting the aspect ratioUsing the remote control Using the OSD menuAbout the aspect ratio 32 OperationUsing Wall Color Selecting a picture modeOptimizing the image Fine-tuning the image quality in user modes Setting the User 1/User 2 mode2. Go to the PICTURE Picture Mode menu Adjusting BrightnessAdjusting Sharpness Adjusting Brilliant ColorSelecting a color temperature About color temperaturesTo adjust the settings Setting the presentation timer Hiding the image To cancel the timer, perform the following stepsUsing the remote control Using the OSD menuUtilizing FAQ function Freezing the image3. Press Mode/Enter Operating in a high altitude environment Locking control keysTo activate the High Altitude Mode Adjusting the sound Personalizing the projector menu displayAdjusting the sound level Turning off the Power On/Off Ring ToneControlling the projector through a Lan environment MP526/MP576 only Configuring the Lan Control SettingsIf you are in a DHCP environment If you are in a non-DHCP environmentSee Remote control on page 12 for Controlling the projector remotely through a web browserii. You can adjust the Lan Control Settings Shutting down the projector Menu operation Menu systemSETUP SETUPDisable/30 min/1 hr/2 hr/3 hr/4 hr/8 Power On/Off RingReset All Settings 48 OperationDescription of each menu surface is not white. See Using Wall Color on page 33 forSelecting a picture mode on page 33 for details mode on page 34 for detailsSee Adjusting Brilliant Color on page 35 for details Saves the settings made for User 1 or User 2 modeSee Switching input signal on page 30 for details See 3D Color Management on page 35 for detailsMenu Display Time Menu PositionOff on page 55 for details the image on page 38 for detailsVolume See Adjusting the sound on page 41 for detailsLamp Mode Reset Lamp TimerClosed Caption Enable Picture ModeResolution Caption VersionMaintenance Cleaning the lensCleaning the projector case Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Setting Lamp Mode as EconomicTiming of replacing the lamp the inconvenience when the projector runs out ofperformance. If the projector is normally run with 2950 hours. A new lamp should be fitted to avoidReplacing the lamp Do not turn the power on with the lamp cover removed3. Turn the projector over. Then loosen the screws on the lamp cover 4. Remove the lamp cover from the projector58 Maintenance Resetting the lamp timer Indicators Power eventsLight Status & DescriptionTroubleshooting Remote control does not workThe password is incorrect The projector does not turn onSpecifications OpticalElectrical MechanicalDimensions Ceiling mount installationCeiling mount screws M4 x 8 Max. L = 8 mmTiming chart Supported timing for PC inputPixel Frequency Frequency HzSupported timing for Component-YPbPr input Supported timing for Video and S-Video inputsHorizontal Frequency kHz Vertical FrequencyWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement WEEE directiveAccessibility Requirements for Rehabilitation Act of 1973, Section 68 Regulation statements